| Electronic Components Datasheet Search |
|
MAX1652EEE Datasheet(PDF) 10 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX1652EEE Datasheet(HTML) 10 Page - Maxim Integrated Products |
|
10 / 28 page ![]() High-Efficiency, PWM, Step-Down DC-DC Controllers in 16-Pin QSOP 10 ______________________________________________________________________________________ Standard Application Circuits It’s easy to adapt the basic MAX1653 single-output 3.3V buck converter (Figure 1) to meet a wide range of appli- cations with inputs up to 30V (limited by choice of exter- nal MOSFET). Simply substitute the appropriate components from Table 1 (candidate suppliers are pro- vided in Table 2). These circuits represent a good set of trade-offs among cost, size, and efficiency while staying within the worst-case specification limits for stress-relat- ed parameters such as capacitor ripple current. Don’t change the frequency of these circuits without first recalculating component values (particularly induc- tance value at maximum battery voltage). For a discussion of dual-output circuits using the MAX1652 and MAX1654, see Figure 9 and the Secondary Feedback-Regulation Loop section. Detailed Description The MAX1652 family are BiCMOS, switch-mode power- supply controllers designed primarily for buck-topology regulators in battery-powered applications where high efficiency and low quiescent supply current are critical. The parts also work well in other topologies such as boost, inverting, and Cuk due to the flexibility of their floating high-speed gate driver. Light-load efficiency is enhanced by automatic idle-mode operation—a vari- able-frequency pulse-skipping mode that reduces losses due to MOSFET gate charge. The step-down power-switching circuit consists of two N-channel MOSFETs, a rectifier, and an LC output filter. The out- put voltage is the average of the AC voltage at the switching node, which is adjusted and regulated by changing the duty cycle of the MOSFET switches. The gate-drive signal to the N-channel high-side MOSFET must exceed the battery voltage and is provided by a flying capacitor boost circuit that uses a 100nF capaci- tor connected to BST. MAX1653 CSL CSH VL SYNC FB V+ 10 11 5 7 14 Q1 Q2 16 15 13 D2 CMPSH-3 J1 150kHz/300kHz JUMPER NOTE: KEEP CURRENT-SENSE LINES SHORT AND CLOSE TOGETHER. SEE FIGURE 8. D1 12 8 9 REF 3 GND 4 +5V AT 5mA +3.3V OUTPUT GND OUT BST DH LX DL 2 1 LOW-NOISE CONTROL PGND SKIP SS 6 ON/OFF CONTROL SHDN INPUT REF OUTPUT +2.5V AT 100 µA C5 0.33 µF C4 4.7 µF C7 0.1 µF C6 0.01 µF (OPTIONAL) C1 C2 C3 0.1 µF R1 L1 Figure 1. Standard 3.3V Application Circuit (see Table 1 for Component Values) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |