SC2200 datasheet(259/433 Pages) NSC

259 / 433 page

Revision 3.0

259

www.national.com

Core Logic Module (Continued)

GPIO_EN. Allow GPIOs (GPIO47-GPIO32 and GPIO15-GPIO0) to generate an SCI.

0: Disable.

1: Enable.

F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled for PME generation. This bit (GPIO_EN) globally enables

those selected GPIOs for generation of an SCI.

2:1

Reserved. Must be set to 0.

PWR_U_REQ_EN. Allow power-up request events from the SuperI/O module to generate an SCI.

0: Disable.

1: Enable.

A power-up request event is defined as any of the following events/activities: Modem, Telephone, Keyboard, Mouse, CEIR

(Consumer Electronic Infrared)

Offset 14h

GPWIO Control Register 1 (R/W)

Reset Value: 00h

7:4

Reserved. Must be set to 0.

Reserved.

GPWIO2_POL. Select GPWIO2 polarity.

0: Active high

1: Active low

GPWIO1_POL. Select GPWIO1 polarity.

0: Active high

1: Active low

GPWIO0_POL. Select GPWIO0 polarity.

0: Active high

1: Active low

Offset 15h

GPWIO Control Register 2 (R/W)

Reset Value: 00h

Reserved.

GPWIO_SMIEN2. Allow GPWIO2 to generate an SMI.

0: Disable. (Default)

1: Enable.

A fixed high-to-low or low-to-high transition (debounce period) of 31 µs exists in order for GPWIO2 to be recognized.

Bit 2 of this register must be set to 0 (input) for GPWIO2 to be able to generate an SMI.

If asserted, this bit overrides the setting of F1BAR1+I/O Offset 12h[10] and its status is reported in F1BAR0+I/O Offset

00h/02h[0].

GPWIO_SMIEN1. Allow GPWIO1 to generate an SMI.

0: Disable. (Default)

1: Enable.

See F1BAR1+I/O Offset 07h[3] for debounce information.

Bit 1 of this register must be set to 0 (input) for GPWIO1 to be able to generate an SMI.

If asserted, this bit overrides the setting of F1BAR1+I/O Offset 12h[9] and its status is reported in F1BAR0+I/O Offset

00h/02h[0].

GPWIO_SMIEN0. Allow GPWIO0 to generate an SMI.

0: Disable. (Default)

1: Enable.

See F1BAR1+I/O Offset 07h[3] for debounce information.

Bit 0 of this register must be set to 0 (input) for GPWIO0 to be able to generate an SMI.

If enabled, this bit overrides the setting of F1BAR1+I/O Offset 12h[8] and its status is reported in F1BAR0+I/O Offset

00h/02h[0].

Reserved.

GPWIO2_DIR. Selects the direction of GPWIO2.

0: Input.

1: Output.

Table 5-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)

Bit

Description

SC2200 Datasheet(PDF) 259 Page - National Semiconductor (TI)

SC2200 Datasheet(HTML) 259 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL