| Electronic Components Datasheet Search |
|
ADT75 Datasheet(PDF) 19 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADT75 Datasheet(HTML) 19 Page - Analog Devices |
|
19 / 25 page ![]() ADT75 Data Sheet Rev. B | Page 18 of 24 FRAME 1 SERIAL BUS ADDRESS BYTE FRAME 2 ADDRESS POINTER REGISTER BYTE ACK. BY ADT75 ACK. BY ADT75 ACK. BY ADT75 STOP BY MASTER FRAME 4 DATA BYTE SCL SDA START BY MASTER 1 0 0 1 A2 A1 A0 P7 P6 P5 P4 P3 P2 P1 P0 9 D7 D6 D5 D4 D3 D2 D1 D0 R/W 1 9 1 9 1 ACK. BY ADT75 FRAME 3 DATA BYTE SDA (CONTINUED) SCL (CONTINUED) D15 D14 D13 D12 D11 D10 D9 D8 9 1 Figure 16. Writing to the Address Pointer Register Followed by Two Bytes of Data to Either THYST or TOS Registers SCL SDA 1 1 0 0 1 A2 A1 A0 START BY MASTER FRAME 1 SERIAL BUS ADDRESS BYTE FRAME 2 DATA BYTE FROM CONFIGURATION REGISTER STOP BY MASTER ACK. BY ADT75 NO ACK. BY MASTER R/W D7 D6 D5 D4 D3 D2 D1 D0 9 9 1 Figure 17. Reading Back Data from the Configuration Register FRAME 1 SERIAL BUS ADDRESS BYTE FRAME 2 MSB DATA BYTE FROM TEMPERATURE VALUE REGISTER ACK. BY ADT75 ACK. BY MASTER SCL SDA START BY MASTER 1 0 0 1 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 9 R/W 1 9 1 NO ACK. BY MASTER STOP BY MASTER FRAME 3 LSB DATA BYTE FROM TEMPERATURE VALUE REGISTER SDA (CONTINUED) SCL (CONTINUED) D7 D6 D5 D4 D3 D2 D1 D0 9 1 Figure 18. Reading Back Data from the Temperature Value Register READING DATA Reading data from the ADT75 is done in a one data byte operation for the configuration register and a two data byte operation for the temperature value register, THYST register, and the TOS setpoint register. Reading back the contents of the configuration register is shown in Figure 17. Reading back the contents of the temperature value register is shown in Figure 18. Reading back from any register first requires a single-byte write operation to the address pointer register to set up the register address of the register that is going to be read from. To read from another register, execute another write to the address pointer register to set up the relevant register address. Thus, block reads are not possible, that is, there is no I2C auto-increment. If the address pointer register has previously been set up with the address of the register that is going to receive a read command then there is no need to repeat a write operation to set up the register address again. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |