S29GL032A datasheet(52/95 Pages) SPANSION

52 / 95 page

S29GL-A

S29GL-A_00_A11 September 10, 2007

Da ta

Sh e e t

Command Definitions

Writing specific address and data commands or sequences into the command register initiates device

operations. Table 10.2 on page 61 and Table 10.1 on page 62 define the valid register command sequences.

Writing incorrect address and data values or writing them in the improper sequence may place the device in

an unknown state. A reset command is then required to return the device to reading array data.

All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on

the rising edge of WE# or CE#, whichever happens first. Refer to AC Characteristics on page 72 for timing

diagrams.

9.1

Reading Array Data

The device is automatically set to reading array data after device power-up. No commands are required to

retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded

Erase algorithm.

After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after

which the system can read data from any non-erase-suspended sector. After completing a programming

operation in the Erase Suspend mode, the system may once again read array data with the same exception.

See Erase Suspend/Erase Resume Commands on page 60 for more information.

The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if

DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See

Reset Command on page 52 for more information.

See also Requirements for Reading Array Data in Device Bus Operations on page 22 for more information.

The Read-Only Operations–AC Characteristics on page 72 provide the read parameters, and Figure 16.2

on page 74 shows the timing diagram.

9.2

Reset Command

Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t

cares for this command.

The reset command may be written between the sequence cycles in an erase command sequence before

erasing begins. This resets the device to the read mode. Once erasure begins, however, the device ignores

reset commands until the operation is complete.

The reset command may be written between the sequence cycles in a program command sequence before

programming begins. This resets the device to the read mode. If the program command sequence is written

while the device is in the Erase Suspend mode, writing the reset command returns the device to the erase-

suspend-read mode. Once programming begins, however, the device ignores reset commands until the

operation is complete.

The reset command may be written between the sequence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command must be written to return to the read mode. If the device

entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device

to the erase-suspend-read mode.

If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the

read mode (or erase-suspend-read mode if the device was in Erase Suspend).

Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the Write-to-

Buffer-Abort Reset command sequence to reset the device for the next operation.

S29GL032A Datasheet(PDF) 52 Page - SPANSION

S29GL032A Datasheet(HTML) 52 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95

Datasheet Download

Link URL