Electronic Components Datasheet Search
  English  ▼

X  

LM5171 Datasheet(PDF) 4 Page - Texas Instruments

Part # LM5171
Description  LM5171-Q1 Dual Channel Bidirectional Controller
PDF  89 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

LM5171 Datasheet(HTML) 4 Page - Texas Instruments

  LM5171 Datasheet HTML 1Page - Texas Instruments LM5171 Datasheet HTML 2Page - Texas Instruments LM5171 Datasheet HTML 3Page - Texas Instruments LM5171 Datasheet HTML 4Page - Texas Instruments LM5171 Datasheet HTML 5Page - Texas Instruments LM5171 Datasheet HTML 6Page - Texas Instruments LM5171 Datasheet HTML 7Page - Texas Instruments LM5171 Datasheet HTML 8Page - Texas Instruments LM5171 Datasheet HTML 9Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 89 page
background image
Table 4-1. Pin Functions (continued)
PIN
I/O(1)
DESCRIPTION
NO.
NAME
10
EN2
I
CH-2 enable pin. Pulling EN2 above 2V turns off the SS/DEM2 pulldown and allows CH-2 to begin a soft-start
sequence. Pulling EN2 below 1 V discharges the SS/DEM2 capacitor and holds it low. The high side and low
side gate drivers of both channels are held in the low state when SS/DEM2 is discharged.
11
DIR2
I
CH-2 direction command input. Pulling DIR2 pin above 2V sets the converter to buck mode. Pulling DIR2 below
1V sets the converter to the boost mode. If the DIR2 pin is left open, the device detects an invalid command and
disables CH-2 with the MOSFET gate drivers in the low state.
12
VDD
P
Output of 5V internal LDO. Connect a 1μF capacitor between the VDD pin and AGND.
13
HV2
I
Connect to HV-Port for CH-2 controller.
14
HB2
I
CH-2 high-side gate driver bootstrap supply. Connect a 0.22μF capacitor between the pin and SW2. Connect a
Zener diode between the pin and SW2 to protect the high side driver from overvoltage.
15
HO2
O
CH-2 high-side gate driver output. Connect to the gate of the high-side N-channel MOSFET through a short, low
inductance path.
16
SW2
P
CH-2 switching node. Connect directly to the source of the high-side N-channel MOSFET.
17
LO2
O
CH-2 low-side gate driver output. Connect to the gate of the low-side N-channel MOSFET through a short, low
inductance path.
18
PGND
G
Power ground connection pin for low-side gate drivers and VCC bias supply.
19
VCC
P
VCC bias supply pin. Connect a 2.2μF capacitor between the VCC pin and AGND.
20
LO1
O
CH-1 low-side gate driver output. Connect to the gate of the low-side N-channel MOSFET through a short, low
inductance path.
21
SW1
P
CH-1 switch node. Connect directly to the source of the high-side N-channel MOSFET.
22
HO1
O
CH-1 high-side gate driver output. Connect to the gate of the high-side N-channel MOSFET through a short, low
inductance path.
23
HB1
I
CH-1 high-side gate driver bootstrap supply input. Connect a 0.22μF capacitor between the pin and SW1.
Connect a Zener diode between the pin and SW1 to protect the high side driver from overvoltage.
24
HV1
I
Connect to the HV-Port for CH-1 controller.
25
LDODRV
O
The LDO MOSFET driver. Connect to the LDO MOSFET gate to get a regulated 9V VCC. Leave this pin open
when it is not used.
26
DIR1
I
CH-1 direction command input. Pulling DIR1 pin above 2V sets the converter to buck mode. Pulling DIR1 below
1V sets the converter to the boost mode. If the DIR1 pin is left open, the device detects an invalid command and
disables CH-1 with the MOSFET gate drivers in the low state.
27
EN1
I
CH-1 enable pin. Pulling EN1 above 2V turns off the SS1 pulldown and allows CH-1 to begin a soft-start
sequence. Pulling EN1 below 1 V discharges the SS1 capacitor and holds it low. The high side and low side
gate drivers of both channels are held in the low state when SS1 is discharged.
28
SS/DEM1
I
ISET1 soft-start pin. The SS/DEM1-pin also sets CH-1 in either DEM or FPWM. An external capacitor sets the
ramp rate of the SS/DEM1 pin voltage during soft start. SS/DEM1 overrides ISET1 voltage during soft-start.
When an outer voltage loop is used, use 100pF soft-start capacitor. A 60.4kΩ resistor between SS/DEM1 and
AGND sets CH-1 to DEM. CH-1 operates in FPWM without the resistor.
29
COMP1
O
Output of the CH-1 trans-conductance (gm) error amplifier and the inverting input of the CH-1 PWM comparator.
Connect a loop compensation network to this pin.
30
ISET1
I
CH-1 current programming pin. There is 1V offset on ISET1, that is, the CH-1 inductor current is proportional
to (ISET1-1V). In DEM, the inductor current is 0 when ISET1 is less than1V. In FPWM, the inductor current
reverses when ISET1 is less than 1V.
31
CSB1
I
CH-1 differential current sense inputs. The CH-1 current sense resistor is placed between these two pins. The
CSA1 pin connects to the power inductor and CSB1 pin connects to the LV-Port.
32
CSA1
I
33
IMON1
O
CH-1 current monitor pin. A current source flows out of this pin. The current source is proportional to the CH-1
inductor current or CH-1 boost mode output current based on CFG selection. Placing a terminating resistor and
filter capacitor from IMON1 to AGND produces a DC voltage representing the CH-1 DC current level. An internal
50μA offset DC current source at the IMON1 pin raises the active signal above the ground noise, thus improving
the monitor noise immunity.
34
ERRHV
O
Output of the error amplifier for boost mode. This error amplifier is active when DIR1 is low.
35
FBHV
I
Inverting input of the error amplifier for boost mode. This error amplifier is active when DIR1 is low.
LM5171-Q1
SNVSC75B – APRIL 2023 – REVISED SEPTEMBER 2025
www.ti.com
4
Submit Document Feedback
Copyright © 2025 Texas Instruments Incorporated
Product Folder Links: LM5171-Q1



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com