Electronic Components Datasheet Search
  English  ▼

X  

LTC6602 Datasheet(PDF) 21 Page - Linear Technology

Part # LTC6602
Description  Dual Matched, High Frequency Bandpass/Lowpass Filters
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LTC6602 Datasheet(HTML) 21 Page - Linear Technology

Back Button LTC6602 Datasheet HTML 17Page - Linear Technology LTC6602 Datasheet HTML 18Page - Linear Technology LTC6602 Datasheet HTML 19Page - Linear Technology LTC6602 Datasheet HTML 20Page - Linear Technology LTC6602 Datasheet HTML 21Page - Linear Technology LTC6602 Datasheet HTML 22Page - Linear Technology LTC6602 Datasheet HTML 23Page - Linear Technology LTC6602 Datasheet HTML 24Page - Linear Technology LTC6602 Datasheet HTML 25Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 28 page
background image
LTC6602
21
6602fa
APPLICATIONS INFORMATION
Figure 13. Two Filters in a Master/Slave Configuration
If the lowpass cutoff frequency varies then the Figure 12b
circuit must be used.
The output common mode voltage is equal to the voltage
of the VOCM pin. The VOCM pin is biased to one half of the
supply voltage by an internal resistive divider (see Block
Diagram). To alter the common mode output voltage, VOCM
can be driven with an external voltage source or resistor
network. If external resistors are used, it is important to
note that the internal 1.6k resistors can vary ±30% (their
ratio varies only ±1%). The filter outputs can also be AC
coupled.
The LTC6602 can be interfaced to an A/D converter by pull-
ing CLKCNTL (Pin 5) to V+D.ThisconfiguresCLKIO(Pin15)
as a clock output, which can be used to drive the clock
input of the A/D converter. This allows the A/D converter
to be synchronized with the filter sampling clock, avoiding
“beat frequencies” and simplifying the board layout. Any
routing attached to the CLKIO pin should be as short as
possible, in order to minimize ringing.
Similarly, two LTC6602s can be connected in a master/
slave configuration as shown in Figure 13. This results
in four matched filter channels, all synchronized to the
same clock. The master has its CLKCNTL pin pulled to
V+D, configuring its CLKIO pin as an output, while the
slave has its CLKCNTL pin pulled to ground, configuring
its CLKIO pin as an input.
Output Drive
The filter outputs can drive 1k and/or 50pF loads connected
to AC ground with a 0.5V to 2.5V signal (corresponding
to a 4VP-P differential signal). For differential loads (loads
connected between +OUTA and –OUTA or +OUTB and
–OUTB) the outputs can produce a 4VP-P signal across 2k
and/or 25pF. For smaller signal amplitudes, the outputs can
drive correspondingly heavier loads. For larger capacitive
loads, an external 50Ω series resistor is recommended
for each output.
V+IN
V+A
V+D
+INA
–INA
CLKCNTL
CLKIO
GND
LTC6602
MASTER
VOUT1
VIN1
0.1μF
+
–
+
–
+
–
+
–
6602 F13
+OUTA
–OUTA
RBIAS
3.3V
LTC6602
SLAVE
VOUT2
VIN2
0.1μF
+OUTA
–OUTA
3.3V
V+IN
V+A
V+D
+INA
–INA
CLKCNTL
CLKIO
GND
RBIAS
RBIAS
RBIAS



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com