| Electronic Components Datasheet Search |
|
COP685BC Datasheet(PDF) 7 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
COP685BC Datasheet(HTML) 7 Page - National Semiconductor (TI) |
|
7 / 57 page ![]() DC Electrical Characteristics COP684BC: (Continued) −55˚C ≤ T A ≤ +125˚C Parameter Conditions Min Typ Max Units Maximum Input Current without Latchup (Notes 8, 10) Room Temp ±100 mA RAM Retention Voltage, V r (Note 9) 500 ns Rise and Fall Time 2.0 V Input Capacitance (Note 10) 7 pF Load Capacitance on D2 1000 pF Note 8: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than VCC and the pins will have sink current to VCC when biased at voltages greater than VCC (the pins do not have source current when biased at a voltage below VCC). The effective resistance to VCC is 750Ω (typical). These two pins will not latch up. The voltage at the pins must be limited to less than 14V. Note 9: Condition and parameter valid only for part in HALT mode. Note 10: Parameter characterized but not tested. AC Electrical Characteristics COP684BC and COP884BC: −55˚C ≤ T A ≤ +125˚C Parameter Conditions Min Typ Max Units Instruction Cycle Time (t c) Crystal/Resonator V CC ≥ 4.5V 1.0 DC µs Inputs t SETUP V CC ≥ 4.5V 200 ns t HOLD V CC ≥ 4.5V 60 ns PWM Capture Input t SETUP V CC ≥ 4.5V 30 ns t HOLD V CC ≥ 4.5V 70 ns Output Propagation Delay (t PD1,tPD0) (Note 12) C L = 100 pF, RL = 2.2 kΩ SK, SO V CC ≥ 4.5V 0.7 µs PWM Outputs V CC ≥ 4.5V 75 ns All Others V CC ≥ 4.5V 1 µs MICROWIRE Setup Time (t UWS) (Note 13) 20 ns Hold Time (t UWH) (Note 13) 56 ns Output Prop Delay (t UPD) 220 ns Input Pulse Width (Note 14) Interrupt High Time 1 t c Interrupt Low Time 1 t c Timer 1,2 High Time 1 t c Timer 1,2 Low Time 1 t c Reset Pulse Width (Note 13) 1.0 µs Power Supply Rise Time for Proper 50 µs 256*t c Operation of On-Chip RESET Note 11: For device testing purposes of all AC parameters, VOH will be tested at 0.5*VCC. Note 12: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs. Note 13: Parameter not tested. Note 14: tc = Instruction Cycle Time. www.national.com 7 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |