Electronic Components Datasheet Search
  English  ▼

X  

AD9144BCPZ Datasheet(PDF) 67 Page - Analog Devices

Part # AD9144BCPZ
Description  Digital-to-Analog Converter
PDF  125 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD9144BCPZ Datasheet(HTML) 67 Page - Analog Devices

Back Button AD9144BCPZ Datasheet HTML 63Page - Analog Devices AD9144BCPZ Datasheet HTML 64Page - Analog Devices AD9144BCPZ Datasheet HTML 65Page - Analog Devices AD9144BCPZ Datasheet HTML 66Page - Analog Devices AD9144BCPZ Datasheet HTML 67Page - Analog Devices AD9144BCPZ Datasheet HTML 68Page - Analog Devices AD9144BCPZ Datasheet HTML 69Page - Analog Devices AD9144BCPZ Datasheet HTML 70Page - Analog Devices AD9144BCPZ Datasheet HTML 71Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 67 / 125 page
background image
Data Sheet
AD9144
Rev. B | Page 67 of 125
DIGITAL DATAPATH
INPUT
POWER
DETECTION
AND
PROTECTION
INTERPOLATION
MODES
1×, 2×, 4×, 8×
COARSE
AND
FINE
MODULATION
INV
SINC
DIGITAL GAIN,
PHASE OFFSET,
DC OFFSET,
AND
GROUP DELAY
ADJUSTMENT
Figure 69. Block Diagram of Digital Datapath
The block diagram in Figure 69 shows the functionality of the
digital datapath (all blocks can be bypassed). The digital
processing includes an input power detection block; three half-
band interpolation filters; a quadrature modulator consisting of a
fine resolution NCO and fDAC/4 and fDAC/8 coarse modulation
block; an inverse sinc filter; and gain, phase, offset, and group
delay adjustment blocks.
The interpolation filters take independent I and Q data streams.
If using the modulation function, I and Q must be quadrature
data to function properly.
Note that the pipeline delay changes when digital datapath
functions are enabled/disabled. If fixed DAC pipeline latency
is desired, do not reconfigure these functions after initial
configuration.
DUAL PAGING
Digital datapath registers are paged to allow configuration of
either DAC dual independently or both simultaneously. Table 65
shows how to use the dual paging register.
Table 65. Paging Modes
DUAL_PAGE,
Reg. 0x008[1:0]
Duals
Paged
DACs Updated
1
A
DAC0 and DAC1
2
B
DAC2 and DAC3
3 (default)
A and B
DAC0, DAC1, DAC2, and DAC3
Several functions are paged by DAC dual, such as input data
format, downstream protection, interpolation, modulation,
inverse sinc, digital gain, phase offset, dc offset, group delay, IQ
swap, datapath PRBS, LMFC sync, and NCO alignment.
DATA FORMAT
BINARY_FORMAT (Register 0x110[7], paged as described in
the Dual Paging section) controls the expected input data
format. By default it is 0, which means that the input data must
be in twos complement. It can also be set to 1, which means
input data is in offset binary (0x0000 is negative full scale and
0xFFFF is positive full scale).
INTERPOLATION FILTERS
The transmit path contains three half-band interpolation filters,
which each provides a 2× increase in output data rate and a low-
pass function. The filters can be cascaded to provide a 4× or 8×
interpolation ratio. Table 66 shows how to select each available
interpolation mode, their usable bandwidths, and their
maximum data rates. Note that fDATA = fDAC/InterpolationFactor.
Interpolation mode is paged as described in the Dual Paging
section. Register 0x030[0] is high if an unsupported
interpolation mode is selected.
Table 66. Interpolation Modes and Usable Bandwidth
Interpolation
Mode
INTERP_MODE,
Reg 0x112[2:0]
Usable
Bandwidth
Maximum
fDATA (MHz)
1× (Bypass)
0x00
0.5 × fDATA
10601
2×
0x01
0.4 × fDATA
10601
4×
0x03
0.4 × fDATA
700
8×
0x04
0.4 × fDATA
350
1 The maximum speed for 1× and 2× interpolation is limited by the JESD204B
interface.
Filter Performance
The interpolation filters interpolate between existing data in
such a way that they minimize changes in the incoming data
while suppressing the creation of interpolation images. This is
shown for each filter in Figure 70.
The usable bandwidth (as shown in Table 66) is defined as the
frequency band over which the filters have a pass-band ripple of
less than ±0.001 dB and an image rejection of greater than 85 dB.
0
–20
–40
–60
–80
–100
0
0.2
0.4
0.6
0.8
1.0
FREQUENCY (×
fDAC)
2×
4×
8×
Figure 70. All Band Responses of Interpolation Filters



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com