Electronic Components Datasheet Search
  English  ▼

X  

AD9144BCPZ Datasheet(PDF) 69 Page - Analog Devices

Part # AD9144BCPZ
Description  Digital-to-Analog Converter
PDF  125 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD9144BCPZ Datasheet(HTML) 69 Page - Analog Devices

Back Button AD9144BCPZ Datasheet HTML 65Page - Analog Devices AD9144BCPZ Datasheet HTML 66Page - Analog Devices AD9144BCPZ Datasheet HTML 67Page - Analog Devices AD9144BCPZ Datasheet HTML 68Page - Analog Devices AD9144BCPZ Datasheet HTML 69Page - Analog Devices AD9144BCPZ Datasheet HTML 70Page - Analog Devices AD9144BCPZ Datasheet HTML 71Page - Analog Devices AD9144BCPZ Datasheet HTML 72Page - Analog Devices AD9144BCPZ Datasheet HTML 73Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 69 / 125 page
background image
Data Sheet
AD9144
Rev. B | Page 69 of 125
NCO Phase Offset
The phase offset feature allows rotation of the I and Q phases.
Unlike phase adjust, this feature moves the phases of both I and
Q channels together. Phase offset can be used only when using
NCO fine modulation.
−180° ≤ DegreesOffset < +180°
PhaseOffset = (DegreesOffset/180°) × 215
where PhaseOffset is a 16-bit twos complement number.
The NCO phase offset is set as shown in Table 69 and paged as
described in the Dual Paging section. Because this function is
part of the fine modulation block, phase offset is not updated
immediately upon writing. Instead, it updates on the rising edge
of FTW_ UPDATE_REQ (Register 0x113[0]) along with the FTW.
Table 69. NCO Phase Offset Registers
Address
Value
0x11A
PhaseOffsetI[7:0]
0x11B
PhaseOffset[15:8]
INVERSE SINC
The AD9144 provides a digital inverse sinc filter to compensate
the DAC roll-off over frequency. The filter is enabled by setting
the INVSINC_ENABLE bit (Register 0x111[7], paged as
described in the Dual Paging section) and is enabled by default.
The inverse sinc (sinc−1) filter is a seven-tap FIR filter. Figure 73
shows the frequency response of sin(x)/x roll-off, the inverse
sinc filter, and the composite response. The composite response
has less than ±0.05 dB pass-band ripple up to a frequency of
0.4 × fDACCLK. To provide the necessary peaking at the upper end
of the pass band, the inverse sinc filter shown has an intrinsic
insertion loss of approximately 3.8 dB; in many cases, this can be
partially compensated as described in the Digital Gain section.
1
0
–1
–2
–3
–4
–5
0
0.05
0.10
0.15
0.20
FREQUENCY (×
fDAC)
0.25
0.30
0.35
0.45
0.40
0.50
SIN(x)/x ROLL-OFF
SINC–1 FILTER RESPONSE
COMPOSITE RESPONSE
Figure 73. Responses of sin(x)/x Roll-Off, the Sinc−1 Filter, and the Composite
of the Two Input Signal Power Detection and Protection
DIGITAL GAIN, PHASE ADJUST, DC OFFSET, AND
GROUP DELAY
Digital gain, phase adjust, and dc offset (as described in the
Digital Gain section, Phase Adjust section, and DC Offset
section) allow compensation of imbalances in the I and Q paths
due to analog mismatches between DAC I/Q outputs, quadrature
modulator I/Q baseband inputs, and DAC/modulator interface
I/Q paths. These imbalances can cause the two following issues:
•
An unwanted sideband signal to appear at the quadrature
modulator output with significant energy. This can be
tuned out using digital gain and phase adjust. Tuning the
quadrature gain and phase adjust values can optimize
complex image rejection in single sideband radios or can
optimize the error vector magnitude (EVM) in zero IF
(ZIF) architectures.
•
The I/Q mismatch can cause LO leakage through a
modulator, which can be tuned out using dc offset.
Group delay allows adjustment of the delay through the DAC,
which can be used to adjust digital predistortion (DPD) loop delay.
Digital Gain
Digital gain can be used to independently adjust the digital
signal magnitude being fed into each DAC. This is useful to
balance the gain between I and Q channels of a dual or to cancel
out the insertion loss of the inverse sinc filter. Digital gain must
be enabled when using the blanking state machine (see the
Downstream Protection section). If digital gain is disabled,
TXENx must be tied high.
Digital gain is enabled by setting the DIG_GAIN_ENABLE bit
(Register 0x111[5], paged as described in the Dual Paging
section). In addition to enabling the function, the amount of
digital gain (GainCode) desired must be programmed. By
default, digital gain is enabled and GainCode is 0xAEA.
0 ≤ Gain ≤ 4095/2048
−∞ dB ≤ dBGain ≤ 6.018 dB
Gain = GainCode × (1/2048)
dBGain = 20 × log10(Gain)
GainCode = 2048 × Gain = 2048 × 10dBGain/20
where GainCode is a 12-bit unsigned binary number.
The I/Q digital gain is set as shown in Table 70 and paged as
described in the Dual Paging section.
The default GainCode (0xAEA = 2.7 dB), is appropriate to
counteract the insertion loss of the inverse sinc filter without
causing digital clipping when using 2× interpolation. This value
can be read off of Figure 73 at 0.25 × fDAC, as that is the Nyquist
rate when using a 2× interpolation. Recommended GainCode
values for 4× and 8× interpolation are 0xBB3 (3.3 dB) and
0xBF8 (3.5 dB), respectively.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com