| Electronic Components Datasheet Search |
|
TFS757 Datasheet(PDF) 13 Page - Power Integrations, Inc. |
|
|
|||||||||||||||||||||||||||||
TFS757 Datasheet(HTML) 13 Page - Power Integrations, Inc. |
|
13 / 36 page ![]() Rev. E 04/15 13 TFS757-764HG www.power.com Output Power Table Product2 Two-Switched Forward 380 V Flyback 100 V - 400 V Continuous1 (25 °C) Continuous1 (50 °C) Peak (50 °C) 50 °C TFS757HG 193 W 163 W 228 W 20 W TFS758HG 236 W 200 W 278 W 20 W TFS759HG 280 W 235 W 309 W 20 W TFS760HG 305 W 258 W 358 W 20 W TFS761HG 326 W 276 W 383 W 20 W TFS762HG 360 W 304 W 407 W 20 W TFS763HG 388 W 327 W 455 W 20 W TFS764HG 414 W 344 W 530 W 20 W Table 5. Output Power Table. Notes: 1. Maximum practical continuous power in an open frame design with adequate heat sinking (assuming heat sink θ C-A of <4 °C/W), measured at specified ambient temperature (see Key Applications Considerations for more information). 2. Package: eSIP16/12. (Note: Direct attach to heat sink, does not require insulation SIL pad) 2. Second a 15 mA threshold (I BP(SD))for standby secondary OVP latch-off. When the BYPASS pin current exceeds this threshold, the standby and main converters are latched-off. This latch can be reset by pulling the LINE-SENSE pin below the line undervoltage threshold (I L(SB-UVOFF)), or by discharging the BYPASS pin below 4.7 V. Note: unlike the TinySwitch-III the HiperTFS BYPASS pin capacitor does not provide any programming capability. Instead the recommended BYPASS pin capacitor should always be a 1 mF (ceramic) capacitor. Main and Standby Line Overvoltage Detection (OV) The overvoltage threshold is included in the device, and can be used to disable the device during overvoltage (with the use of an additional external signal Zener). The overvoltage threshold is set sufficiently high to prevent accidental triggering during boost PFC overshoot conditions. When the overvoltage condition is triggered, it will simultaneously shutdown both the Main and Standby. The overvoltage feature is intended for use with external components (circuitry), to program the overvoltage threshold independently of the undervoltage thresholds (see the Applications section for details). High-Power eSIP Package The HiperTFS package is designed to minimize the physical size of the device, while maintaining a low thermal impedance and sufficient electrical spacing for the pins. The package has 12 functional pins with 4 pins removed for increased pin-to-pin spacing between high-voltage pins. The low-side two-switch forward and flyback MOSFETs have a thermal impedance of less than 1 °C/W to the exposed pad on the back of the package. Since this pad is referenced to the SOURCE pin (Source), it is at electrical ground potential and thus can be connected to the heat sink without need for electrical insulation. The high-side MOSFET is over-molded to achieve electrical isolation and thus also allows direct connection to the heat sink. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |