AM79C975VCW datasheet(144/304 Pages) AMD

144 / 304 page

144

Am79C973/Am79C975

P R E L I M INARY

31-16 RES

Reserved locations. Written as

zeros and read as undefined.

15-12 RES

Reserved locations. Read and

written as zeros.

11-0

NRBC

Next Receive Byte Count. This

field is a copy of the BCNT field of

RMD1 of the next receive de-

scriptor.

Read/Write accessible only when

either the STOP or the SPND bit

is set. These bits are unaffected

H_RESET,

S_RESET,

STOP.

CSR45: Next Receive Status

Bit

Name

Description

31-16 RES

Reserved locations. Written as

zeros and read as undefined.

15-0

NRST

Next Receive Status. This field is

a copy of bits 31-16 of RMD1 of

the next receive descriptor.

Read/Write accessible only when

either the STOP or the SPND bit

is set. These bits are unaffected

H_RESET,

S_RESET,

STOP.

CSR46: Transmit Poll Time Counter

Bit

Name

Description

31-16 RES

Reserved locations. Written as

zeros and read as undefined.

15-0

TXPOLL

Transmit Poll Time Counter. This

counter is incremented by the

Am79C973/Am79C975 controller

microcode and is used to trigger

the transmit descriptor ring poll-

ing operation of the Am79C973/

Am79C975 controller.

Read/Write accessible only when

either the STOP or the SPND bit

is set. These bits are unaffected

H_RESET,

S_RESET,

STOP.

CSR47: Transmit Polling Interval

Bit

Name

Description

31-16 RES

Reserved locations. Written as

zeros and read as undefined.

15-0 TXPOLLINT

Transmit Polling Interval. This

Am79C973/Am79C975 controller

will wait between successive poll-

ing operations. The TXPOLLINT

value is expressed as the two’s

complement of the desired inter-

val, where each bit of TXPOL-

LINT represents 1 clock period of

time. TXPOLLINT[3:0] are ig-

nored. (TXPOLLINT[16] is im-

plied

one,

TXPOLLINT[15] is significant and

does not represent the sign of the

two’s complement TXPOLLINT

value.)

The default value of this register

is 0000h. This corresponds to a

polling interval of 65,536 clock

periods

(1.966

when

CLK = 33 MHz). The TXPOL-

LINT value of 0000h is created

during the microcode initialization

routine and, therefore, might not

be seen when reading CSR47 af-

ter H_RESET or S_RESET.

If the user desires to program a

value for POLLINT other than the

default, then the correct proce-

dure is to first set INIT only in

CSR0. Then, when the initializa-

tion sequence is complete, the

user must set STOP (CSR0, bit

2). Then the user may write to

CSR47 and then set STRT in

CSR0. In this way, the default

value of 0000h in CSR47 will be

overwritten with the desired user

value.

If the user does not use the stan-

dard

initialization

procedure

(standard implies use of an initial-

ization block in memory and set-

ting the INIT bit of CSR0), but

instead, chooses to write directly

to each of the registers that are

involved in the INIT operation,

then it is imperative that the user

also writes all zeros to CSR47 as

part of the alternative initialization

sequence.

Read/Write accessible only when

either the STOP or the SPND bit

is set. These bits are unaffected

AM79C975VCW Datasheet(PDF) 144 Page - Advanced Micro Devices

AM79C975VCW Datasheet(HTML) 144 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL