DSP56156ROM datasheet(10/76 Pages) MOTOROLA

10 / 76 page

DSP56156 Data Sheet

MOTOROLA

Pin Descriptions

BB (Bus Busy) — active low input when

not bus master, active low output

when bus master.

This pin is asserted

by the DSP when it becomes the bus

master and it performs an external ac-

cess. It is deasserted when the DSP re-

leases bus mastership. BB becomes an

input when the DSP is no longer the

bus master.

Interrupt and Mode Control

MODA/IRQA

(Mode Select A/External In-

terrupt Request A)

— input. This in-

put has two functions:

• to select the initial chip operating

mode and,

• to allow an external device to request

a DSP interrupt after internal syn-

chronization.

MODA is read and internally latched

in the DSP when the processor exits the

reset state. MODA and MODB select

the initial chip operating mode. Several

clock cycles after leaving the reset state,

the MODA pin changes to the external

interrupt request IRQA. The chip oper-

ating mode can be changed by soft-

ware after reset.

The IRQA input is a synchronized ex-

ternal interrupt request which indi-

cates

that

an external

device is

requesting service. It may be pro-

grammed to be level sensitive or nega-

tive edge triggered. If level sensitive

triggering is selected, an external pull

up resistor is required for wired-OR

operation. If the processor is in the stop

standby state and IRQA is asserted, the

processor will exit the stop state.

MODB/IRQB

(Mode Select B/External In-

terrupt Request B)

— input. This in-

put has two functions:

• to select the initial chip operating

mode and,

• to allow an external device to request

a DSP interrupt after internal syn-

chronization.

MODB is read and internally latched in

the DSP when the processor exits the

reset state. MODA and MODB select

the initial chip operating mode. Several

clock cycles after leaving the reset state,

the MODB pin changes to the external

interrupt request IRQB. After reset, the

chip operating mode can be changed

by software.

The IRQB input is an external interrupt

request which indicates that an exter-

nal device is requesting service. It may

be programmed to be level sensitive or

negative edge triggered. If level sensi-

tive triggering is selected, an external

pull up resistor is required for wired-

OR operation.

MODC (Mode Select C)

— input. This input

selects the initial bus operating mode.

When tied high, the external bus is pro-

grammed in the master mode (BR out-

put and BG input) and when tied low

the bus is programmed in the slave

mode (BR input and BG output).

MODC is read and internally latched in

the DSP when the processor exits the

reset state. After RESET, the bus operat-

ing mode can be changed by software by

writing the MC bit of the OMR register.

RESET (Reset)

— input. This input is a direct

hardware reset of the processor. When

RESET is asserted, the DSP is initialized

and placed in the reset state. A Schmitt

Interrupt and Mode Control

Bus Control

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

DSP56156ROM Datasheet(PDF) 10 Page - Motorola, Inc

DSP56156ROM Datasheet(HTML) 10 Page - Motorola, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

Datasheet Download

Link URL