| Electronic Components Datasheet Search |
|
DWM3000 Datasheet(PDF) 12 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
DWM3000 Datasheet(HTML) 12 Page - List of Unclassifed Manufacturers |
|
12 / 24 page ![]() DWM3000 Datasheet © Qorvo 2020 Preliminary Version 0.1 Page 12 SIGNAL NAME PIN I/O (Default) DESCRIPTION EXTON 1 DO (O-L) External device enable. Asserted during wake up process and held active until device enters sleep mode. Can be used to control external DC-DC converters or other circuits that are not required when the device is in sleep mode so as to minimize power consumption. GPIO8 / IRQ 22 DIO (O-L) Interrupt Request output from the DWM3000 to the host processor. By default IRQ is an active-high output but may be configured to be active low if required. For correct operation in SLEEP and DEEPSLEEP modes it should be configured for active high operation. This pin will float in SLEEP and DEEPSLEEP states and may cause spurious interrupts unless pulled low externally (100 kΩ recommended). When the IRQ functionality is not being used the pin may be reconfigured as a general purpose I/O line, GPIO8. GPIO7 / SYNC 4 DIO (I) Defaults to operate as a SYNC input. This pin may be reconfigured as a general purpose I/O pin under software control. GPIO6 / EXTRXE / SPIPHA 9 DIO (I) General purpose I/O pin. On power-up it acts as the SPIPHA (SPI phase selection) pin for configuring the SPI mode of operation. After power-up, the pin will default to a General Purpose I/O pin. On engineering samples GPIO6 is on pin 10. GPIO5 / EXTTXE / SPIPOL 10 DIO (I) General purpose I/O pin. On power-up it acts as the SPIPOL (SPI polarity selection) pin for configuring the SPI operation mode. After power-up, the pin will default to a General Purpose I/O pin. On engineering samples GPIO5 is on pin 9. GPIO4 11 DIO (I) General purpose I/O pin. GPIO3 / TXLED 12 DIO (I) General purpose I/O pin. It may be configured for use as a TXLED driving pin that can be used to light a LED following a transmission. GPIO2 / RXLED 13 DIO (I) General purpose I/O pin. It may be configured for use as a RXLED driving pin that can be used to light a LED during receive mode. GPIO1 / SFDLED 14 DIO (I) General purpose I/O pin. It may be configured for use as a SFDLED driving pin that can be used to light a LED when SFD (Start Frame Delimiter) is found by the receiver. GPIO0 / RXOKLED 15 DIO (I) General purpose I/O pin. It may be configured for use as a RXOKLED driving pin that can be used to light a LED on reception of a good frame. RSTn 3 DIO (O-H) Reset pin. Active Low Output. May be pulled low by external open drain driver to reset the DW3000. Power Supplies VDD1 5 P External supply for the Always-On (AON) portion of the chip. VDD3V3 6,7 P 3 V supply pins. Ground GND 8,16, 21,23,24 G Common ground. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |