AT90PWM2 datasheet(82/365 Pages) ATMEL

82 / 365 page

AT90PWM2/3

4317B–AVR–02/05

External Interrupts

The External Interrupts are triggered by the INT3:0 pins. Observe that, if enabled, the

interrupts will trigger even if the INT3:0 pins are configured as outputs. This feature pro-

vides a way of generating a software interrupt. The External Interrupts can be triggered

by a falling or rising edge or a low level. This is set up as indicated in the specification for

the External Interrupt Control Registers – EICRA (INT3:0). When the external interrupt

is enabled and is configured as level triggered, the interrupt will trigger as long as the pin

is held low. Note that recognition of falling or rising edge interrupts on INT3:0 requires

the presence of an I/O clock, described in “Clock Systems and their Distribution” on

page 30. The I/O clock is halted in all sleep modes except Idle mode.

Note that if a level triggered interrupt is used for wake-up from Power-down mode, the

changed level must be held for some time to wake up the MCU. This makes the MCU

less sensitive to noise. The changed level is sampled twice by the Watchdog Oscillator

clock. The period of the Watchdog Oscillator is 1 µs (nominal) at 5.0V and 25

°C. The

frequency of the Watchdog Oscillator is voltage dependent as shown in the “Electrical

Characteristics(1)” on page 308. The MCU will wake up if the input has the required

level during this sampling or if it is held until the end of the start-up time. The start-up

time is defined by the SUT fuses as described in “System Clock” on page 30. If the level

is sampled twice by the Watchdog Oscillator clock but disappears before the end of the

start-up time, the MCU will still wake up, but no interrupt will be generated. The required

level must be held long enough for the MCU to complete the wake up to trigger the level

interrupt.

External Interrupt Control

• Bits 7..0 – ISC31, ISC30 – ISC01, ISC00: External Interrupt 3 - 0 Sense Control

Bits

The External Interrupts 3 - 0 are activated by the external pins INT3:0 if the SREG I-flag

and the corresponding interrupt mask in the EIMSK is set. The level and edges on the

external pins that activate the interrupts are defined in Table 35. Edges on INT3..INT0

are registered asynchronously.The value on the INT3:0 pins are sampled before detect-

ing edges. If edge or toggle interrupt is selected, pulses that last longer than one clock

period will generate an interrupt. Shorter pulses are not guaranteed to generate an inter-

rupt. Observe that CPU clock frequency can be lower than the XTAL frequency if the

XTAL divider is enabled. If low level interrupt is selected, the low level must be held until

the completion of the currently executing instruction to generate an interrupt. If enabled,

a level triggered interrupt will generate an interrupt request as long as the pin is held

low.

Bit

765

432

ISC31

ISC30

ISC21

ISC20

ISC11

ISC10

ISC01

ISC00

EICRA

Read/Write

R/W

Initial Value

000

AT90PWM2 Datasheet(PDF) 82 Page - ATMEL Corporation

AT90PWM2 Datasheet(HTML) 82 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL