IMX6SDLCEC datasheet(18/169 Pages) NXP

18 / 169 page

i.MX 6Solo/6DualLite Applications Processors for Consumer Products, Rev. 9, 11/2018

NXP Semiconductors

Modules List

SSI-1

SSI-2

SSI-3

I2S/SSI/AC97 Interface

Connectivity

Peripherals

The SSI is a full-duplex synchronous interface, which is

used on the AP to provide connectivity with off-chip

audio peripherals. The SSI supports a wide variety of

protocols (SSI normal, SSI network, I2S, and AC-97), bit

depths (up to 24 bits per word), and clock / frame sync

options.

The SSI has two pairs of 8x24 FIFOs and hardware

support for an external DMA controller in order to

minimize its impact on system performance. The

second pair of FIFOs provides hardware interleaving of

a second audio stream that reduces CPU overhead in

use cases where two time slots are being used

simultaneously.

TEMPMON

Temperature Monitor

System Control

Peripherals

The Temperature sensor IP is used for detecting die

temperature. The temperature read out does not reflect

case or ambient temperature. It reflects the temperature

in proximity of the sensor location on the die.

Temperature distribution may not be uniformly

distributed, therefore the read out value may not be the

reflection of the temperature value of the entire die.

TZASC

Trust-Zone Address

Space Controller

Security

The TZASC (TZC-380 by Arm) provides security

address region control functions required for intended

application. It is used on the path to the DRAM

controller.

UART-1

UART-2

UART-3

UART-4

UART-5

UART Interface

Connectivity

Peripherals

Each of the UARTv2 modules support the following

serial data transmit/receive protocols and

configurations:

• 7- or 8-bit data words, 1 or 2 stop bits, programmable

parity (even, odd or none)

• Programmable baud rates up to 5 Mbps.

• 32-byte FIFO on Tx and 32 half-word FIFO on Rx

supporting auto-baud

• IrDA 1.0 support (up to SIR speed of 115200 bps)

• Option to operate as 8-pins full UART, DCE, or DTE

USBOH3

USB 2.0 High Speed

OTG and 3x HS Hosts

Connectivity

Peripherals

USBOH3 contains:

• One high-speed OTG module with integrated HS

USB PHY

• One high-speed Host module with integrated HS

USB PHY

• Two identical high-speed Host modules connected to

HSIC USB ports.

Table 2. i.MX 6Solo/6DualLite Modules List (continued)

Block Mnemonic

Block Name

Subsystem

Brief Description

IMX6SDLCEC Datasheet(PDF) 18 Page - NXP Semiconductors

IMX6SDLCEC Datasheet(HTML) 18 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL