IMX6SDLCEC datasheet(72/169 Pages) NXP

72 / 169 page

i.MX 6Solo/6DualLite Applications Processors for Consumer Products, Rev. 9, 11/2018

NXP Semiconductors

Electrical Characteristics

For DDR Toggle mode, Figure 33 shows the timing diagram of NAND_DQS/NAND_DATAxx read valid

window. The typical value of tDQSQ is 1.4 ns (max) and 1.4 ns (max) for tQHS at 133 MB/s. GPMI will

sample NAND_DATA[7:0] at both rising and falling edge of an delayed NAND_DQS signal, which is

provided by an internal DPLL. The delay value of this register can be controlled by GPMI register

GPMI_READ_DDR_DLL_CTRL.SLV_DLY_TARGET (see the GPMI chapter of the i.MX

6Solo/6DualLite reference manual). Generally, the typical delay value is equal to 0x7 which means 1/4

clock cycle delay expected. But if the board delay is big enough and cannot be ignored, the delay value

should be made larger to compensate the board delay.

4.11

External Peripheral Interface Parameters

The following subsections provide information on external peripheral interfaces.

4.11.1

AUDMUX Timing Parameters

The AUDMUX provides a programmable interconnect logic for voice, audio, and data routing between

internal serial interfaces (SSIs) and external serial interfaces (audio and voice codecs). The AC timing of

AUDMUX external pins is governed by the SSI module. For more information, see the respective SSI

electrical specifications found within this document.

4.11.2

ECSPI Timing Parameters

This section describes the timing parameters of the ECSPI blocks. The ECSPI have separate timing

parameters for master and slave modes.

NF28 Data write setup

tDS6

0.25

× tCK - 0.32

—

NF29 Data write hold

tDH6

0.25

× tCK - 0.79

—

NF30 NAND_DQS/NAND_DQ read setup skew

tDQSQ7

—3.18

NF31 NAND_DQS/NAND_DQ read hold skew

tQHS7

—3.27

1 The GPMI toggle mode output timing can be controlled by the module’s internal registers

HW_GPMI_TIMING0_ADDRESS_SETUP, HW_GPMI_TIMING0_DATA_SETUP, and HW_GPMI_TIMING0_DATA_HOLD.

This AC timing depends on these registers settings. In the table, AS/DS/DH represents each of these settings.

AS minimum value can be 0, while DS/DH minimum value is 1.

3 T = tCK (GPMI clock period) -0.075ns (half of maximum p-p jitter).

4 CE_DELAY represents HW_GPMI_TIMING2[CE_DELAY]. NF18 is guaranteed by the design. Read/Write operation is started

with enough time of ALE/CLE assertion to low level.

5 PRE_DELAY+1)

≥ (AS+DS).

6 Shown in Figure 34, Samsung Toggle Mode Data Write Timing diagram.

7 Shown in Figure 33, NAND_DQS/NAND_DQ Read Valid Window.

Table 48. Samsung Toggle Mode Timing Parameters1 (continued)

Parameter

Symbol

Timing

T = GPMI Clock Cycle

Unit

Min

Max

IMX6SDLCEC Datasheet(PDF) 72 Page - NXP Semiconductors

IMX6SDLCEC Datasheet(HTML) 72 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL