DP83849IFVSSLASHNOPB datasheet(94/108 Pages) TI2

94 / 108 page

DP83849IF

SNOSAX8D – JUNE 2009 – REVISED APRIL 2013

www.ti.com

10.3.3

TDR Control Register (TDR_CTRL), Page 2, address 16h

This register contains control for the Time Domain Reflectometry (TDR) cable diagnostics. The TDR cable

diagnostics sends pulses down the cable and captures reflection data to be used to estimate cable length

and detect certain cabling faults.

Table 10-28. TDR Control Register (TDR_CTRL), address 16h

Bit

Bit Name

Default

Description

TDR_ENABLE

0, RW

TDR Enable:

Enable TDR mode. This forces powerup state to correct operating

condition for sending and receiving TDR pulses.

TDR_100Mb

0, RW

TDR 100Mb:

Sets TDR controller to use the 100Mb Transmitter. This allows for

sending pulse widths in multiples of 8ns. Pulses in 100Mb mode will

alternate between positive pulses and negative pulses.

Default operation uses the 10Mb Link Pulse generator. Pulses may

include just the 50ns preemphasis portion of the pulse or the 100ns full

link pulse (as controlled by setting TDR Width).

TX_CHANNEL

0, RW

Transmit Channel Select:

Select transmit channel for sending pulses. Pulse can be sent on the

Transmit or Receive pair.

0 : Transmit channel

1 : Receive channel

RX_CHANNEL

0, RW

Receive Channel Select:

Select receive channel for detecting pulses. Pulse can be monitored on

the Transmit or Receive pair.

0 : Transmit channel

1 : Receive channel

SEND_TDR

0, RW/SC

Send TDR Pulse:

Setting this bit will send a TDR pulse and enable the monitor circuit to

capture the response. This bit will automatically clear when the capture is

complete.

10:8

TDR_WIDTH

0, RW

TDR Pulse Width:

Pulse width in clocks for the transmitted pulse. In 100Mb mode, pulses

are in 8ns increments. In 10Mb mode, pulses are in 50ns increments, but

only 50ns or 100ns pulses can be sent. Sending a pulse of 0 width will

not transmit a pulse, but allows for baseline testing.

TDR_MIN_MODE

0, RW

Min/Max Mode control:

This bit controls direction of the pulse to be detected. Default looks for a

positive peak. Threshold and peak values will be interpreted appropriately

based on this bit.

0 : Max Mode, detect positive peak

1 : Min Mode, detect negative peak

RESERVED

0, RO

RESERVED: Writes ignored, read as 0.

5:0

RX_THRESHOLD

<10_0000>, RW

RX Threshold:

This value provides a threshold for measurement to the start of a peak. If

Min Mode is set to 0, data must be greater than this value to trigger a

capture. If Min Mode is 1, data must be less than this value to trigger a

capture. Data ranges from 0x00 to 0x3F, with 0x20 as the midpoint.

Positive data is greater than 0x20, negative data is less than 0x20.

Submit Documentation Feedback

Product Folder Links: DP83849IF

DP83849IFVS/NOPB Datasheet(PDF) 94 Page - Texas Instruments

DP83849IFVS/NOPB Datasheet(HTML) 94 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL