DP83848JSQ datasheet(22/80 Pages) TI

22 / 80 page

www.national.com

RMII mode requires a 50 MHz oscillator be connected to

the device X1 pin. A 50 MHz crystal is not supported.

To tolerate potential frequency differences between the 50

MHz reference clock and the recovered receive clock, the

receive RMII function includes a programmable elasticity

buffer. The elasticity buffer is programmable to minimize

propagation delay based on expected packet size and

clock accuracy. This allows for supporting a range of

packet sizes including jumbo frames.

The elasticity buffer will force Frame Check Sequence

errors for packets which overrun or underrun the FIFO.

Underrun and Overrun conditions can be reported in the

RMII and Bypass Register (RBR). The following table indi-

cates how to program the elasticity buffer fifo (in 4-bit incre-

ments) based on expected max packet size and clock

accuracy. It assumes both clocks (RMII Reference clock

and far-end Transmitter clock) have the same accuracy

3.3 802.3U MII SERIAL MANAGEMENT INTER-

FACE

3.3.1 Serial Management Register Access

The serial management MII specification defines a set of

thirty-two 16-bit status and control registers that are acces-

sible through the management interface pins MDC and

MDIO. The DP83848J implements all the required MII reg-

isters as well as several optional registers. These registers

are fully described in Section 7.0. A description of the serial

management access protocol follows.

3.3.2 Serial Management Access Protocol

The serial control interface consists of two pins, Manage-

ment Data Clock (MDC) and Management Data Input/Out-

put (MDIO). MDC has a maximum clock rate of 25 MHz

and no minimum rate. The MDIO line is bi-directional and

may be shared by up to 32 devices. The MDIO frame for-

mat is shown below in Table 5..

The MDIO pin requires a pull-up resistor (1.5 k

Ω) which,

during IDLE and turnaround, will pull MDIO high. In order to

initialize the MDIO interface, the station management entity

sends a sequence of 32 contiguous logic ones on MDIO to

provide the DP83848J with a sequence that can be used to

establish synchronization. This preamble may be gener-

ated either by driving MDIO high for 32 consecutive MDC

clock cycles, or by simply allowing the MDIO pull-up resis-

tor to pull the MDIO pin high during which time 32 MDC

clock cycles are provided. In addition, 32 MDC clock cycles

should be used to re-sync the device if an invalid start,

opcode, or turnaround bit is detected.

The DP83848J waits until it has received this preamble

sequence before responding to any other transaction.

Once the DP83848J serial management port has been ini-

tialized no further preamble sequencing is required until

after a power-on/reset, invalid Start, invalid Opcode, or

invalid turnaround bit has occurred.

The Start code is indicated by a <01> pattern. This assures

the MDIO line transitions from the default idle line state.

Turnaround is defined as an idle bit time inserted between

the Register Address field and the Data field. To avoid con-

tention during a read transaction, no device shall actively

drive the MDIO signal during the first bit of Turnaround.

The addressed DP83848J drives the MDIO with a zero for

the second bit of turnaround and follows this with the

required data. Figure 4 shows the timing relationship

between MDC and the MDIO as driven/received by the Sta-

tion (STA) and the DP83848J (PHY) for a typical register

read access.

For write transactions, the station management entity

writes data to the addressed DP83848J thus eliminating

the requirement for MDIO Turnaround. The Turnaround

time is filled by the management entity by inserting <10>.

Figure 5 shows the timing relationship for a typical MII reg-

ister write access.

Table 4. Supported packet sizes at +/-50ppm +/-100ppm for each clock

Start Threshold

RBR[1:0]

Latency Tolerance

Recommended Packet Size

at +/- 50ppm

Recommended Packet Size

at +/- 100ppm

1 (4-bits)

2 bits

2400 bytes

1200 bytes

2 (8-bits)

6 bits

7200 bytes

3600 bytes

3 (12-bits)

10 bits

12000 bytes

6000 bytes

0 (16-bits)

14 bits

16800 bytes

8400 bytes

Table 5. Typical MDIO Frame Format

MII Management

Serial Protocol

Read Operation

Write Operation

DP83848JSQ Datasheet(PDF) 22 Page - Texas Instruments

DP83848JSQ Datasheet(HTML) 22 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

Datasheet Download

Link URL