AM79C972BVCW datasheet(88/130 Pages) AMD

88 / 130 page

Am79C972

MPSE (BCR4-7, bit 9) must be set to 1 to enable that

function.

Note: The polarity of the LED pin can be programmed

to be active HIGH by setting LEDPOL (BCR4-7, bit 14)

to 1.

Once a Magic Packet frame is detected, the PCnet-

FAST+ controller will discard the frame internally, but

will not resume normal transmit and receive operations

until PG is asserted or MPEN is cleared. Once both of

these events has occurred, indicating that the system

has detected the Magic Packet and is awake, the con-

troller will continue polling receive and transmit de-

scriptor rings where it left off. It is not necessary to re-

initialize the device. If the part is reinitialized, then the

descriptor locations will be reset and the PCnet-FAST+

controller will not start where it left off.

If magic packet mode is disabled by the assertion of

PG, then in order to immediately re-enable Magic

Packet mode, the PG pin must remain asserted for at

least 200 ns before it is deasserted. If Magic Packet

mode is disabled by clearing MPEN bit, then it may be

immediately re-enabled by setting MPEN back to 1.

The PCI bus interface clock (CLK) is not required to be

running while the device is operating in Magic Packet

mode. Either of the INTA, the LED pins, RWU or the

PME signal may be used to indicate the receipt of a

Magic Packet frame when the CLK is stopped. If the

system wishes to stop the CLK, it will do so after en-

abling the Magic Packet mode.

CAUTION: To prevent unwanted interrupts from other

active parts of the PCnet-FAST+ controller, care must

be taken to mask all likely interruptible events during

Magic Packet mode. An example would be the inter-

rupts from the Media Independent Interface, which

could occur while the device is in Magic Packet mode.

IEEE 1149.1 (1990) Test Access Port

Interface

An IEEE 1149.1-compatible boundary scan Test Ac-

cess Port is provided for board-level continuity test and

diagnostics. All digital input, output, and input/output

pins are tested. The following paragraphs summarize

the IEEE 1149.1-compatible test functions imple-

mented in the Am79C972 controller.

Boundary Scan Circuit

The boundary scan test circuit requires four pins (TCK,

TMS, TDI, and TDO), defined as the Test Access Port

(TAP). It includes a finite state machine (FSM), an in-

struction register, a data register array, and a power-on

reset circuit. Internal pull-up resistors are provided for

the TDI, TCK, and TMS pins.

TAP Finite State Machine

The TAP engine is a 16-state finite state machine

(FSM), driven by the Test Clock (TCK), and the Test

Mode Select (TMS) pins. An independent power-on

reset circuit is provided to ensure that the FSM is in the

TEST_LOGIC_RESET state at power-up. Therefore,

the TRST is not provided. The FSM is also reset when

TMS and TDI are high for five TCK periods.

Supported Instructions

In addition to the minimum IEEE 1149.1 requirements

(BYPASS, EXTEST, and SAMPLE instructions), three

additional instructions (IDCODE, TRIBYP, and SET-

BYP) are provided to further ease board-level testing.

All unused instruction codes are reserved. See Table

12 for a summary of supported instructions.

Instruction Register and Decoding Logic

After the TAP FSM is reset, the IDCODE instruction is

always invoked. The decoding logic gives signals to con-

trol the data flow in the Data registers according to the

current instruction.

Boundary Scan Register

Each Boundary Scan Register (BSR) cell has two

stages. A flip-flop and a latch are used for the Serial

Shift Stage and the Parallel Output Stage, respectively.

There are four possible operation modes in the BSR

cell shown in Table 13.

Table 12.

IEEE 1149.1 Supported Instruction

Summary

Instructio

Name

Instructi

Code

Description

Mode

Selected

Data

EXTEST

0000

External Test

Test

BSR

IDCODE

0001

ID Code

Inspection

Normal

ID REG

SAMPLE

0010

Sample

Boundary

Normal

BSR

TRIBYP

0011

Force Float

Normal

Bypass

SETBYP

0100

Control

Boundary To

1/0

Test

Bypass

BYPASS

1111

Bypass Scan

Normal

Bypass

Table 13.

BSR Mode Of Operation

Capture

Shift

Update

System Function

AM79C972BVCW Datasheet(PDF) 88 Page - Advanced Micro Devices

AM79C972BVCW Datasheet(HTML) 88 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL