AM79C975VCW datasheet(174/304 Pages) AMD

174 / 304 page

174

Am79C973/Am79C975

P R E L I M INARY

GNT at the beginning of the burst

transaction. If EXTREQ is set to

1, REQ stays asserted until the

last but one data phase of the

burst transaction is done. This

mode is useful for systems that

implement an arbitration scheme

without preemption and require

that REQ stays asserted through-

out the transaction.

EXTREQ should not be set to 1

when the Am79C973/Am79C975

controller is used in a PCI bus ap-

plication.

Read accessible always, write

accessible only when either the

STOP or the SPND bit is set. EX-

TREQ is cleared by H_RESET

and is not affected by S_RESET

or STOP.

DWIO

Double Word I/O. When set, this

bit indicates that the Am79C973/

Am79C975

controller

pro-

grammed for DWord I/O (DWIO)

mode. When cleared, this bit indi-

cates

that

the

Am79C973/

Am79C975

controller

pro-

grammed for Word I/O (WIO)

mode. This bit affects the I/O Re-

source Offset map and it affects

the

defined

width

the

Am79C973/Am79C975

control-

lers I/O resources. See the DWIO

and WIO sections for more de-

tails.

The initial value of the DWIO bit is

determined by the programming

of the EEPROM.

The value of DWIO can be al-

tered

automatically

the

Am79C973/Am79C975

control-

ler. Specifically, the Am79C973/

Am79C975

controller

will

set

DWIO if it detects a DWord write

access to offset 10h from the

Am79C973/Am79C975 controller

I/O base address (corresponding

to the RDP resource).

Once the DWIO bit has been set

to a 1, only a H_RESET or an EE-

PROM read can reset it to a 0.

(Note that the EEPROM read op-

eration will only set DWIO to a 0 if

the appropriate bit inside of the

EEPROM is set to 0.)

Read accessible always. DWIO

is read only, write operations

have no effect. DWIO is cleared

by H_RESET and is not affected

S_RESET or by setting the STOP

bit.

BREADE

Burst Read Enable. When set,

this bit enables burst mode during

memory read accesses. When

cleared, this bit prevents the de-

vice from performing bursting

during

read

accesses.

The

Am79C973/Am79C975 controller

can perform burst transfers when

reading the initialization block,

the descriptor ring entries (when

SWSTYLE = 3) and the buffer

memory.

BREADE should be set to 1 when

the Am79C973/Am79C975 con-

troller is used in a PCI bus appli-

cation to guarantee maximum

performance.

Read accessible always; write

accessible only when either the

STOP or the SPND bit is set.

BREADE is cleared by H_RESET

and is not affected by S_RESET

or STOP.

BWRITE

Burst Write Enable. When set,

this bit enables burst mode during

memory write accesses. When

cleared, this bit prevents the de-

vice from performing bursting

during

write

accesses.

The

Am79C973/Am79C975 controller

can perform burst transfers when

writing the descriptor ring entries

(when SWSTYLE = 3) and the

buffer memory.

BWRITE should be set to 1 when

the Am79C973/Am79C975 con-

troller is used in a PCI bus appli-

cation to guarantee maximum

performance.

Read accessible always, write

accessible only when either the

STOP or the SPND bit is set.

BWRITE is cleared by H_RESET

AM79C975VCW Datasheet(PDF) 174 Page - Advanced Micro Devices

AM79C975VCW Datasheet(HTML) 174 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL