 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
FXLS8967AF Datasheet(PDF) 11 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
FXLS8967AF Datasheet(HTML) 11 Page - NXP Semiconductors |
|
|
11 / 98 page  NXP Semiconductors FXLS8967AF 3-Axis Low-g Accelerometer VDD = 1.8 V to 3.0 V, T = –40 °C to 105 °C, unless otherwise noted. Typical values represent mean or mean ±1 σ values, depending on the specific parameter. Symbol Parameter Conditions Min Typ Max Unit TPULSE-THRES1 Motion detection threshold selection 1 – Pulse width range BT_MODE = VDD 562.5 625 883 µs TPULSE-THRES2 Motion detection threshold selection 2 – Pulse width range BT_MODE = VDD 1125 1250 1570 µs TPULSE-THRES3 Motion detection threshold selection 3 – Pulse width range BT_MODE = VDD 2250 2500 2950 µs TPULSE-DRDY DRDY interrupt output pulse width BT_MODE = GND 29 32 35.6 µs TPULSE-BOOT1 BT_MODE = GND 58 64 71.2 µs TPULSE-BOOT2 BOOT interrupt output pulse width BT_MODE = VDD 9 10 11.2 ms ODRTOL Output Data Rate frequency tolerance — –10 ±2.5 10 %ODR TFLT-MOT_DET MOT_DET pin deglitch filter time BT_MODE = VDD — 10 — µs BT_MODE = GND, SPI_CS_ B / WAKE_UP pin — 400 — TFLT-WAKE_UP MOT_DET, WAKE_UP pin deglitch filter time (transition out of Hibernate mode) BT_MODE = VDD, MOT_DET pin — 850 — ns TBOOT1 Time needed to enter Standby mode after POR or soft reset BT_MODE = GND — — 1 ms TBOOT2 Time needed to enter Motion Detection mode after POR or soft reset BT_MODE = VDD, MOT_DET = 1 — — 17.7 ms IDDBOOT Boot sequence peak current draw T = –40 °C to +105 °C; with no decoupling capacitors on VDD pin — — 5 mA TON Transition time (Standby mode to Active mode with valid data output) — — 528.5 µs + 0.9984 * (DEC – 1) * (1/(ODR * DEC))[2] — s TOP Operating temperature range — –40 — +105 °C Table 8. Electrical characteristics...continued [1] Max spec covers the situation where an interrupt pulse is issued by the sensor at the same time the host MCU drives MOT_DET low to signal a hibernate command. In that case, their durations add up. [2] DEC = decimation factor. The selected ODR and operating mode determines the decimation factor. See Section 15.13 for more information on setting or determining the measurement decimation factor. In LPM, the DEC factor is fixed at 1, making the time to first sample output fixed at 528.5 μs (typ), independent of the selected ODR. FXLS8967AF All information provided in this document is subject to legal disclaimers. © NXP B.V. 2021. All rights reserved. Objective data sheet Rev. 1 — 27 April 2021 11 / 98 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
