Changes from Revision E (September 2013) to Revision F (June 2015)

Page

• Changed Features section..................................................................................................................................1

• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device

Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout

section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information

section ............................................................................................................................................................... 1

• Changed Device Comparison Table .................................................................................................................. 5

• Changed Pin Functions table..............................................................................................................................6

• Changed Open Loop Gain vs Frequency graph............................................................................................... 15

• Changed Input Referred Noise vs Frequency graph ....................................................................................... 15

• Changed Open Loop Gain vs Frequency graph .............................................................................................. 20

• Changed Input Referred Noise vs Frequency graph........................................................................................ 20

Changes from Revision D (October 2011) to Revision E (September 2013)

Page

• Added OPA2836 RMC package to document.....................................................................................................1

• Added RMC pin definitions to Pin Functions table..............................................................................................6

• Deleted Packaging/Ordering Information table, leaving only note to POA......................................................... 8

• Added OPA2836 RMC package to Thermal Information table........................................................................... 9

Changes from Revision C (September 2011) to Revision D (September 2011)

Page

• Removed Product Preview from OPA835IRUNT and OPA835IRUNR............................................................... 5

• Removed Product Preview from OPA836IRUNT and OPA836IRUNR............................................................... 8

• Changed typical value for resistor temperature coefficien parameter from TBD to < 10.................................... 9

• Changed "quiescent operating current" parameter to "quiescent operating current per amplifier".....................9

• Changed resistor temperature coefficient typical value from TBD to < 10........................................................12

• Changed "quiescent operating current" to "quiescent operating current per amplifier".................................... 12

Changes from Revision B (May 2011) to Revision C (August 2011)

Page

• Added the "The OPA836 RUN package..." text to the Description..................................................................... 1

• Removed Product Preview from all devices except OPA835IRUNT and OPA835IRUNR..................................5

• Removed Product Preview from all devices except OPA836IRUNT and OPA836IRUNR..................................8

• Changed typical value for channel to channel crosstalk (OPA2836) parameter from TBD to –120 dB..............9

• Changed the common-mode rejection ratio minimum value from 94 dB to 91 dB............................................. 9

• Added Gain Setting Resistors (OPA836IRUN ONLY) parameter in Electrical Characteristics table.................. 9

• Changed the quiescent operating current (TA = 25°C) minimum value from 0.8 mA to 0.7 mA.........................9

• Changed the minimum value for power supply rejection (±PSRR) parameter from 95 dB to 91 dB.................. 9

• Changed the power-down pin bias current test condition from PD = 0.7 V to PD = 0.5 V..................................9

• Changed the power-down quiescent current test condition from PD = 0.7 V to PD = 0.5 V...............................9

• Changed typical value for channel to channel crosstalk (OPA2836) parameter from TBD to –120 dB............12

• Changed the Common-mode rejection ratio Min value From: 97 dB To: 94 dB............................................... 12

• Added GAIN SETTING RESISTORS (OPA836I RUN ONLY) parameter to Electrical Characteristics table....12

• Changed the quiescent operating current (TA = 25°C) minimum value from 0.9 mA to 0.8 mA.......................12

• Changed the power supply rejection (±PSRR) minimum value from: 97 dB to 94 dB......................................12

• Changed the Power-down quiescent current CONDITIONS From: PD = 0.7 V To: PD = 0.5 V.......................12

• Changed the Power-down quiescent current Conditions From: PD = 0.7 V To: PD = 0.5 V............................ 12

• Added Figure Crosstalk vs Frequency..............................................................................................................15

• Added Crosstalk vs Frequency figure...............................................................................................................20

• Added section Single Ended to Differential Amplifier ...................................................................................... 32

www.ti.com

OPA836, OPA2836

SLOS712J – JANUARY 2011 – REVISED MARCH 2021

Copyright © 2021 Texas Instruments Incorporated

Submit Document Feedback

3

Product Folder Links: OPA836 OPA2836