R8C2H datasheet(71/367 Pages) RENESAS

71 / 367 page

R8C/2H Group, R8C/2J Group

6. Voltage Detection Circuit

Rev.1.00

Mar 28, 2008

Page 51 of 341

REJ09B0388-0100

6.4

Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset

Table 6.4 lists the Procedure for Setting Bits Associated with Voltage Monitor 2 Interrupt and Reset. Figure 6.13

shows an Example of Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Operation. To use the voltage

monitor 2 interrupt or voltage monitor 2 reset to exit stop mode, set the VW2C1 bit in the VW2C register to 1

(digital filter disabled).

NOTES:

1. Set the VW2C7 bit to 1 (when VCC reaches Vdet2 or below) for the voltage monitor 2 reset.

2. When the VW2C0 bit is set to 0, steps 4 and 5 can be executed simultaneously (with 1 instruction).

Table 6.4

Procedure for Setting Bits Associated with Voltage Monitor 2 Interrupt and Reset

Step

When Using Digital Filter

When Not Using Digital Filter

Voltage Monitor 2

Interrupt

Voltage Monitor 2

Reset

Voltage Monitor 2

Interrupt

Voltage Monitor 2

Reset

Set the COMPSEL bit in the PINSR4 register to 0 (voltage monitor 1, voltage monitor 2)

Set the VCA27 bit in the VCA2 register to 1 (voltage detection 2 circuit enabled)

Wait for td(E-A)

Select the sampling clock of the digital filter

by the VW2F0 to VW2F1 bits in the VW2C

Set the VW2C1 bit in the VW2C register to 1

(digital filter disabled)

5(2)

Set the VW2C1 bit in the VW2C register to 0

(digital filter enabled)

−

Select the timing of the interrupt and reset

request by the VCAC2 bit in the VCAC

Select the timing of the interrupt and reset

request by the VCAC2 bit in the VCAC

Set the VW2C6 bit in

the VW2C register to

0 (voltage monitor 2

interrupt mode)

Set the VW2C6 bit in

the VW2C register to

1 (voltage monitor 2

reset mode)

Set the VW2C6 bit in

the VW2C register to

0 (voltage monitor 2

interrupt mode)

Set the VW2C6 bit in

the VW2C register to

1 (voltage monitor 2

reset mode)

Set the VW2C2 bit in the VW2C register to 0 (Vdet2 crossing is not detected)

Set the CM14 bit in the CM1 register to 0

(low-speed on-chip oscillator on)

−

Wait for 2 cycles of the sampling clock of the

digital filter

− (No wait time required)

Set the VW2C0 bit in the VW2C register to 1 (voltage monitor 2 interrupt/reset enabled)

R8C2H Datasheet(PDF) 71 Page - Renesas Technology Corp

R8C2H Datasheet(HTML) 71 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL