XIO2001 datasheet(45/131 Pages) TI

45 / 131 page

3.10.4 Accessing Serial-Bus Devices Through Software

3.11 Advanced Error Reporting Registers

3.12 Data Error Forwarding Capability

XIO2001 PCI Express™ to PCI Bus Translation Bridge

www.ti.com

SCPS212B – MAY 2009 – REVISED JULY 2009

The bridge provides a programming mechanism to control serial-bus devices through system software.

The programming is accomplished through a doubleword of PCI configuration space at offset B0h.

Table 3-9 lists the registers that program a serial-bus device through software.

Table 3-9. Registers Used To Program Serial-Bus Devices

PCI OFFSET

DESCRIPTION

B0h

Serial-bus data (see

Contains the data byte to send on write commands or the received data byte on read

Section 4.55)

commands.

B1h

Serial-bus word address

The content of this register is sent as the word address on byte writes or reads. This register is

(see Section 4.56)

not used in the quick command protocol. Bit 7 (PROT_SEL) in the serial-bus control and status

B2h

Serial-bus slave address

Write transactions to this register initiate a serial-bus transaction. The slave device address and

(see Section 4.57)

the R/W command selector are programmed through this register.

B3h

Serial-bus control and

Serial interface enable, busy, and error status are communicated through this register. In

status (see Section 4.58)

addition, the protocol-select bit (PROT_SEL) and serial-bus test bit (SBTEST) are programmed

through this register.

To access the serial EEPROM through the software interface, the following steps are performed:

1. The control and status byte is read to verify the EEPROM interface is enabled (SBDETECT asserted)

and not busy (REQBUSY and ROMBUSY deasserted).

2. The serial-bus word address is loaded. If the access is a write, then the data byte is also loaded.

3. The serial-bus slave address and R/W command selector byte is written.

4. REQBUSY is monitored until this bit is deasserted.

5. SB_ERR is checked to verify that the serial-bus operation completed without error. If the operation is a

read, then the serial-bus data byte is now valid.

In the extended PCI Express configuration space, the bridge supports the advanced error reporting

capabilities structure. For the PCI Express interface, both correctable and uncorrectable error statuses are

provided. For the PCI bus interface, secondary uncorrectable error status is provided. All uncorrectable

status bits have corresponding mask and severity control bits. For correctable status bits, only mask bits

are provided.

Both the primary and secondary interfaces include first error pointer and header log registers. When the

first error is detected, the corresponding bit position within the uncorrectable status register is loaded into

the first error pointer register. Likewise, the header information associated with the first failing transaction

is loaded into the header log. To reset this first error control logic, the corresponding status bit in the

uncorrectable status register is cleared by a writeback of 1b.

For systems that require high data reliability, ECRC is fully supported on the PCI Express interface. The

primary side advanced error capabilities and control register has both ECRC generation and checking

enable control bits. When the checking bit is asserted, all received TLPs are checked for a valid ECRC

field. If the generation bit is asserted, then all transmitted TLPs contain a valid ECRC field.

The bridge supports the transfer of data errors in both directions.

If a downstream PCI Express transaction with a data payload is received that targets the internal PCI bus

and the EP bit is set indicating poisoned data, then the bridge must ensure that this information is

transferred to the PCI bus. To do this, the bridge forces a parity error on each PCI bus data phase by

inverting the parity bit calculated for each double-word of data.

Submit Documentation Feedback

Feature/Protocol Descriptions

XIO2001 Datasheet(PDF) 45 Page - Texas Instruments

XIO2001 Datasheet(HTML) 45 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL