| Electronic Components Datasheet Search |
|
ADF4351 Datasheet(PDF) 4 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADF4351 Datasheet(HTML) 4 Page - Analog Devices |
|
4 / 28 page ![]() ADF4351 Data Sheet Rev. 0 | Page 4 of 28 Parameter Min Typ Max Unit Test Conditions/Comments Minimum RF Output Power3 −4 dBm Programmable in 3 dB steps Maximum RF Output Power3 5 dBm Output Power Variation ±1 dB Minimum VCO Tuning Voltage 0.5 V Maximum VCO Tuning Voltage 2.5 V NOISE CHARACTERISTICS VCO Phase Noise Performance VCO noise is measured in open-loop conditions −89 dBc/Hz 10 kHz offset from 2.2 GHz carrier −114 dBc/Hz 100 kHz offset from 2.2 GHz carrier −134 dBc/Hz 1 MHz offset from 2.2 GHz carrier −148 dBc/Hz 5 MHz offset from 2.2 GHz carrier −86 dBc/Hz 10 kHz offset from 3.3 GHz carrier −111 dBc/Hz 100 kHz offset from 3.3 GHz carrier −134 dBc/Hz 1 MHz offset from 3.3 GHz carrier −145 dBc/Hz 5 MHz offset from 3.3 GHz carrier −83 dBc/Hz 10 kHz offset from 4.4 GHz carrier −110 dBc/Hz 100 kHz offset from 4.4 GHz carrier −131 dBc/Hz 1 MHz offset from 4.4 GHz carrier −145 dBc/Hz 5 MHz offset from 4.4 GHz carrier Normalized Phase Noise Floor (PN SYNTH) 4 PLL loop BW = 500 kHz −220 dBc/Hz ABP = 6 ns −221 dBc/Hz ABP = 3 ns Normalized 1/f Noise (PN 1_f) 5 10 kHz offset; normalized to 1 GHz −116 dBc/Hz ABP = 6 ns −118 dBc/Hz ABP = 3 ns In-Band Phase Noise −100 dBc/Hz 3 kHz from 2111.28 MHz carrier Integrated RMS Jitter6 0.27 ps Spurious Signals Due to PFD Frequency −80 dBc Level of Signal with RF Mute Enabled −40 dBm 1 I CP is internally modified to maintain constant loop gain over the frequency range. 2 T A = 25°C; AVDD = DVDD = VVCO = 3.3 V; prescaler = 8/9; fREFIN = 100 MHz; fPFD = 25 MHz; fRF = 4.4 GHz. 3 Using 50 Ω resistors to V VCO, into a 50 Ω load. Power measured with auxiliary RF output disabled. The current consumption of the auxiliary output is the same as for the main output. 4 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 log N (where N is the N divider value) and 10 log fPFD. To calculate in-band phase noise performance as seen at the VCO output, use the following formula: PNSYNTH = PNTOT − 10 log(fPFD) − 20 log N. 5 The PLL phase noise is composed of flicker (1/f) noise plus the normalized PLL noise floor. The formula for calculating the 1/f noise contribution at an RF frequency (f RF) and at a frequency offset (f) is given by PN = PN1_f + 10 log(10 kHz/f) + 20 log(fRF/1 GHz). Both the normalized phase noise floor and flicker noise are modeled in ADIsimPLL. 6 f REFIN = 122.88 MHz; fPFD = 30.72 MHz; VCO frequency = 4222.56 MHz; RFOUT = 2111.28 MHz; N = 137; loop BW = 60 kHz; ICP = 2.5 mA; low noise mode. The noise was measured with an EVAL-ADF4351EB1Z and the Rohde & Schwarz FSUP signal source analyzer. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |