TMS320DM641 datasheet(143/171 Pages) TI

143 / 171 page

Multichannel Buffered Serial Port (McBSP)

143

June 2003 − Revised August 2004

SPRS222C

Table 4−50. Timing Requirements for McBSP as SPI Master or Slave:

CLKSTP = 10b, CLKXP = 1†‡ (see Figure 4−46)

NO.

−400

−500

−600

UNIT

NO.

MASTER

SLAVE

UNIT

MIN

MAX

MIN

MAX

tsu(DRV-CKXH) Setup time, DR valid before CLKX high

2 − 12P

th(CKXH-DRV)

Hold time, DR valid after CLKX high

5 + 24P

† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.

‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.

Table 4−51. Switching Characteristics Over Recommended Operating Conditions for McBSP as

SPI Master or Slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 4−46)

NO.

PARAMETER

−400

−500

−600

UNIT

NO.

PARAMETER

MASTER§

SLAVE

UNIT

MIN

MAX

MIN

MAX

th(CKXH-FXL)

Hold time, FSX low after CLKX high¶

T − 2

T + 3

td(FXL-CKXL)

Delay time, FSX low to CLKX low#

H − 2.5

H + 3

td(CKXL-DXV)

Delay time, CLKX low to DX valid

−2

12P + 3

20P + 17

tdis(CKXH-DXHZ)

Disable time, DX high impedance following last data bit

from CLKX high

H − 2

H + 3

tdis(FXH-DXHZ)

Disable time, DX high impedance following last data bit

from FSX high

4P + 3

12P + 17

td(FXL-DXV)

Delay time, FSX low to DX valid

8P + 2

16P + 17

† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.

‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.

§ S = Sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)

Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)

T =

CLKX period = (1 + CLKGDV) * S

H =

CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even

= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero

L =

CLKX low pulse width

= (CLKGDV/2) * S if CLKGDV is even

= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero

¶ FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input on FSX

and FSR is inverted before being used internally.

CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP

CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP

# FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master clock

(CLKX).

Bit 0

Bit(n-1)

(n-2)

(n-3)

(n-4)

Bit 0

Bit(n-1)

(n-2)

(n-3)

(n-4)

CLKX

FSX

Figure 4−46. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1

TMS320DM641 Datasheet(PDF) 143 Page - Texas Instruments

TMS320DM641 Datasheet(HTML) 143 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL