AD6653 datasheet(49/80 Pages) AD

49 / 80 page

AD6653

Rev. 0 | Page 49 of 80

MEMORY MAP REGISTER DESCRIPTION

For more information on functions controlled in Register 0x00

to Register 0xFF, see Application Note AN-877, Interfacing to

High Speed ADCs via SPI, at www.analog.com.

SYNC Control (Register 0x100)

Bit 7—Signal Monitor Sync Enable

Bit 7 enables the sync pulse from the external sync input to the

signal monitor block. The sync signal is passed when Bit 7 and

Bit 0 are high. This is continuous sync mode.

Bit 6—Half-Band Next Sync Only

If the master sync enable bit (Register 0x100, Bit 0) and the half-

band sync enable bit (Register 0x100, Bit 5) are high, Bit 6 allows

the NCO32 to synchronize following the first sync pulse it receives

and ignore the rest. If Bit 6 is set, Bit 5 of Register 0x100 resets

after this sync occurs.

Bit 5—Half-Band Sync Enable

Bit 5 gates the sync pulse to the half-band filter. When Bit 5

is set high, the sync signal causes the half-band to resynchro-

nize, starting at the half-band decimation phase selected in

sync enable bit (Register 0x100, Bit 0) is high. This is continuous

sync mode.

Bit 4—NCO32 Next Sync Only

If the master sync enable bit (Register 0x100, Bit 0) and the

NCO32 sync enable bit (Register 0x100, Bit 3) are high, Bit 4

allows the NCO32 to sync following the first sync pulse it receives

and ignores the rest. Bit 3 of Register 0x100 resets after a sync

occurs if Bit 4 is set.

Bit 3—NCO32 Sync Enable

Bit 3 gates the sync pulse to the 32-bit NCO. When this bit is set

high, the sync signal causes the NCO to resynchronize, starting

at the NCO phase offset value. This sync is active only when the

master sync enable bit (Register 0x100, Bit 0) is high. This is

continuous sync mode.

Bit 2—Clock Divider Next Sync Only

If the master sync enable bit (Register 0x100, Bit 0) and the clock

divider sync enable bit (Register 0x100, Bit 1) are high, Bit 2

allows the clock divider to synchronize following the first sync

pulse it receives and ignore the rest. Bit 1 of Register 0x100

resets after it synchronizes.

Bit 1—Clock Divider Sync Enable

Bit 1 gates the sync pulse to the clock divider. The sync signal

is passed when Bit 1 and Bit 0 are high. This is continuous

sync mode.

Bit 0—Master Sync Enable

Bit 0 must be high to enable any of the sync functions.

fS/8 Output Mix Control (Register 0x101)

Bits[7:6]—Reserved

Bits[5:4]—fS/8 Start State

Bit 5 and Bit 4 set the starting phase of the fS/8 output mix.

Bits[3:2]—Reserved

Bit 1—fS/8 Next Sync Only

If the master sync enable bit (Register 0x100, Bit 0) and the fS/8

sync enable bit (Register 0x101, Bit 0) are high, Bit 1 allows the

fS/8 output mix to synchronize following the first sync pulse it

receives and ignore the rest. Bit 0 of Register 0x100 resets after it

synchronizes.

Bit 0—fS/8 Sync Enable

Bit 0 gates the sync pulse to the fS/8 output mix. This sync is

active only when the master sync enable bit (Register 0x100,

Bit 0) is high. This is continuous sync mode.

FIR Filter and Output Mode Control (Register 0x102)

Bits[7:4]—Reserved

Bit 3—FIR Gain

When Bit 3 is set high, the FIR filter path, if enabled, has a gain

of 1. When Bit 3 set low, the FIR filter path has a gain of 2.

Bit 2—fS/8 Output Mix Disable

Bit 2 disables the fS/8 output mix when enabled. Bit 2 should be

set along with Bit 1 to enable complex output mode.

Bit 1—Complex Output Mode Enable

Setting Bit 1 high enables complex output mode.

Bit 0—FIR Filter Enable

When set high, Bit 0 enables the FIR filter. When Bit 0 is

cleared, the FIR filter is bypassed and shut down for power

savings.

Digital Filter Control (Register 0x103)

Bits[7:4]—Reserved

Bit 3—Half-Band Decimation Phase

When set high, Bit 3 uses the alternate phase of the decimating

half-band filter.

Bit 2—Spectral Reversal

Bit 2 enables the spectral reversal feature of the half-band filter.

Bit 1—High-Pass/Low-Pass Select

Bit 1 enables the high-pass mode of the half-band filter when

set high. Setting this bit low enables the low-pass mode (default).

Bit 0—Reserved

Bit 0 reads back as a 1.

AD6653 Datasheet(PDF) 49 Page - Analog Devices

AD6653 Datasheet(HTML) 49 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

Datasheet Download

Link URL