Electronic Components Datasheet Search
  English  ▼

X  

LDDEVALP Datasheet(PDF) 11 Page - Wavelength Electronics, Inc.

Part # LDDEVALP
Description  Low Noise Laser Diode Drivers
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  WAVELENGTH [Wavelength Electronics, Inc.]
Direct Link  https://www.teamwavelength.com/
Logo WAVELENGTH - Wavelength Electronics, Inc.

LDDEVALP Datasheet(HTML) 11 Page - Wavelength Electronics, Inc.

Back Button LDDEVALP Datasheet HTML 7Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 8Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 9Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 10Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 11Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 12Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 13Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 14Page - Wavelength Electronics, Inc. LDDEVALP Datasheet HTML 15Page - Wavelength Electronics, Inc. Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 28 page
background image
© 2025
www.teamWavelength.com
11
LDD P SERIES LASER DIODE DRIVER
CONSTANT CURRENT MODE OPERATION
!
Do not power on the LDD P Series Laser
Diode Driver until all wire connections are
completely attached and the Output
Current Adjust and Limit Current Adjust
trimpots have been correctly configured.
!
Before connecting a power supply to the
LDD P Series Laser Diode Driver, measure
the supply’s output voltage and ensure a
reading between +5 and +12 Volts. Turn
OFF the power supply before connecting
the LDD P.
adjusTing on-BoaRd TRimPoTs
The two trimpots on the LDD P Series are:
Output Current Adjust and Laser Limit Current Adjust
Maximize the Output Current Adjust trimpot. Turn the trimpot
fully clockwise, at least 12 complete turns.
Zero the Laser Limit Current Adjust trimpot. Turn the trimpot
fully counter-clockwise, at least 12 complete turns.
Both adjustments are shown below in
Figure 8.
OUTPUT CURRENT ADJUST
LASER LIMIT CURRENT ADJUST
Figure 8. Adjusting the two on-board trimpots.
measuRe cuRRenT moniToR ouTPuT
Pin 2 (Current Monitor) is used to monitor the current output
to the laser diode. The voltage measured can be converted
to current using the transfer function in
Table 3.
To measure, attach the positive input of a voltmeter to the
current monitor output (pin 2) and the negative input of the
voltmeter to ground (pin 4), as shown in
Figure 9.
CURRENT
FEEDBACK
CURRENT
MONITOR
MOD
GND
1
2
3
4
- +
VOLTMETER
Figure 9. Connect the voltmeter as shown to measure the
power monitor output.
TuRn on VoLTage souRce
Apply power to the LDD P only after all connections have
been thoroughly reviewed. Note the modulation input, pin 3,
must be connected to ground, pin 4, to properly configure
the onboard limit current and laser diode current trimpots.
MOD
GND
1
2
3
4
V+
5
6
7
8
FEEDBACK
LASER DIODE
CONNECTIONS
+5 to +12 Volts
}
Figure 10. Connect pins 3 and 4 (modulation and ground) to
properly configure the LDD P.
adjusT LaseR diode LimiT cuRRenT
Calculate the current monitor voltage that corresponds to
the proper limit current (I
LIMIT) setting. Do not exceed the
maximum operating current of the laser diode.
Ensure that I
LIMIT has units of mA, and use Equation 1 to
calculate what limit voltage (V
LIMIT) should be measured at
pin 2.
Equation 1. V
PIN 2 = VLIMIT = ILIMIT / (TFCM )
where TF
CM is the Current Monitor transfer function (model-
dependent) found in
Table 3 on page 4.
Then, SLOWLY adjust the Limit Current Adjust trimpot
clockwise until the voltmeter attached to the current monitor
(pin 2) reads V
LIMIT.
CURRENT
FEEDBACK
CURRENT
MONITOR
MOD
GND
1
2
3
4
- +
LASER LIMIT
CURRENT ADJUST
SLOWLY
VOLTMETER
Figure 11. Set the Limit Current Adjust trimpot to the limit
voltage.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com