22017 datasheet(62/120 Pages) ITT

62 / 120 page

ARINC 404

DPX*ME Crimp

DPX*MA/ME Coaxial Contact Data (for environmental requirements)

www.ittcannon.com

Dimensions shown in inch (mm)

Specifications and dimensions subject to change

Components/Accessories

RING TYPE RETENTION (A32W2 & A40W1 CONTACT ARRANGEMENTS)

Coaxial Contact Assembly Recommendations

(For Codes A, B, C, D, E, J, K, L and P)

Part Number*

Without Seal (MA)

Sealed (ME)

Seal 1

Seal 2

Ins. Dia.

Size/Max.

'A' Trim

Dim.

Crimp

Tool

Cable Trim

Dimensions

WITHOUT SEAL

SEALED

Cable Accommodation

NOTE:

32W2 (MA Version)

A32W2 (ME Version)

40W1 (MA Version)

A40W1 (ME Version)

.420 (10.67)

.400 (10.16)

(For Codes A, B, C, D, E, J, K, L and P)

SOCKET

BUSHING

SEAL

SEAL 2

SEAL 1

.330 (8.38)

.310 (7.86)

P-249-1397-001

S-249-1398-003

P-249-1399-001

S-249-1400-003

P-249-1401-001

S-249-1402-003

P-249-1403-001

S-249-1404-003

P-249-1405-001

S-249-1406-003

*P for pin, S for socket

†Unsealed accomodates both Seal 1 & Seal 2 Cables.

††For use with connectors supplied less grommet ( Code 29**, etc.)

1. Center contact, rear insulator, crimp ring, support bushing and seal sleeve are packaged separately and

shipped with the coaxial assembly.

2. Use impact extraction tool no. CET-C4 (038869-0004). An insertion tool is not required. (See Item 4).

3. Cable Assembly Instructions

4. To extract coaxial, push back seal sleeve and support bushing. Then push out coaxial from engaging end

with CET-C4 (038869-0004) impact tool.

5. When crimping with CA58073 crimp tool, care should be taken to avoid flaring the front end of the

crimp ring. Place Crimp jaw so that the second tooth of the indentors is over the end of the crimp ring.

6. To facilitate extraction of contacts and avoid splaying the length of free cable adjacent to the rear

surface of the connector should not be less then 2.000 (50.80).

Step 1- If applicable, determine which portion of seal sleeve should be used. If seal 2 is used, cut off

seal 1 portion

Step 2 - In sequence, place seal sleeve, support bushing and crimp ring over cable jacket.

Step 3 - Trim cable per illustration.

Step 4 - Place rear insulator over dielectric.

Step 5 - Solder innerconductor to center contact.

Step 6 - Insert soldered cable firmly into coaxial with shielding over coaxial shell.

Step 7 - Pull crimp ring forward until stopped and crimped.

Step 8 - Insert coaxial assembly into connector until engaged. Push support bushing into grommet

until shoulder rest on tublular extension. Then pull seal sleeve forward until it is snug

against grommet.

P-249-1397-002

S-249-1398-002

P-249-1399-002

S-249-1400-002

P-249-1401-002

S-249-1402-002

P-249-1403-002

S-249-1404-002

P-249-1405-002

S-249-1406-002

RG58B

RG195

RG179B

RG179B, RG196

RG59B, RG62A

RG180B

RG174, RG179B,

RG316

.249 (6.32)

.200 (5.08)

.158 (4.01)]

.113 (2.87)

.083 (2.11)

.435 (11.05)

.415 (10.54)

.460 (11.68)

.440 (11.18)

.460 (11.68)

.440 (11.18)

.460 (11.68)

.440 (11.18)

.480 (12.19)

.460 (11.68)

CA58073

CCT-406M

The A32W2 & A40W1 (Ring Type Retention); AW8 & A32W4 (LITTLE CAESAR Renention) Coaxial Contact arrangements have been

redesigned to provide ease of insertion/removal of the coaxial contacts. Sealing is accomplished with the addiction of sealing sleeves

provided with the coaxial contact assembly.

22017 Datasheet(PDF) 62 Page - ITT Industries

22017 Datasheet(HTML) 62 Page - ITT Industries

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL