LXT6155LE datasheet(18/50 Pages) INTEL

18 / 50 page

LXT6155 — 155 Mbps SDH/SONET/ATM Transceiver

Datasheet

2.3

Clocks

2.3.1

Parallel Mode

The LXT6155 accepts TPICLK synchronized with transmit input parallel data TPID<7:0>. The

data is serialized and transmitted at TTIP0/TRING0 or TTIP1/TRING1 depending on which line

encoding mode is selected. The LXT6155 in turn produces the receive output parallel clock

RPOCLK, that is recovered from incoming line data RTIP/RRING, and is synchronized with

receive output parallel data RPOD<7:0>.

2.3.1.1

Transmit Parallel Input Clock (TPICLK)

TPICLK is the transmit parallel input clock provided by the systems interface. This clock must be

nominally 19.44 MHz, synchronized with parallel input data TPID<7:0>. This clock is then

internally multiplied by 8 to produce a serial clock, used for parallel-to-serial conversion, line

drivers, and pulse reshaping. In HW mode (HWSEL = Low), TPID data is sampled on the falling

edge of TPICLK. In SW mode (HWSEL = High), the clock polarity can be inverted (Reg #0, bit

#3).

2.3.1.2

Receive Parallel Output Clock (RPOCLK)

RPOCLK is the parallel output clock that is recovered from the line input data RTIP/RRING. This

clock is at 19.44 MHz, synchronized with parallel output data RP0D<7:0>. In HW mode (HWSEL

= Low), the RPOCLK clock rising edge is at the center of eye opening of RPOD<7:0> as shown in

Figure 21. In SW mode (HWSEL = High), the clock polarity can be inverted (Reg #0, bit #2).

Under LOS (LOS=High) or Rx PLL loss of lock (LOCK=Low) conditions RPOCLK is switched to

the reference selected by the CIS control in HW mode, or Reg #0 bit #5 in SW mode. Also, the

parallel output is forced to all zeros. This feature can be disabled in SW mode (HWSEL =High)

via register #10, bit #7.

2.3.2

Serial Mode

At the transmit systems interface, the LXT6155 accepts the transmit input clock TSICLKP/

TSICLKN that is synchronized to incoming serial differential data TPOS/TNEG. At the line

interface, the LXT6155 accepts RTIP/RRING data and produces the clocks RSOCLKP/

RSOCLKN synchronized to receive output data RPOS/RNEG. RSOCLKP/RSOCLKN clock edges

are at the center of RPOS/RNEG.

2.3.2.1

Transmit Serial Input Clock (TSICLKP/TSICLKN)

TSICLKP/TSICLKN is the serial input clock from the overhead terminator. This 155.52 MHz

clock is rising edge centered with input serial data on TPOS and TNEG. These clock pins should be

left open when the LXT6155 operates in parallel mode.

2.3.2.2

Receive Serial Output Clock (RSOCLKP/RSOCLKN)

RSOCLKP/RSOCLKN is the serial clock recovered from the line input data on RTIP/RRING. This

155.52 MHz clock is falling edge centered with receive serial output data on RPOS/RNEG. These

clock pins should be left open when the LXT6155 operates in parallel mode. Under LOS

LXT6155LE Datasheet(PDF) 18 Page - Intel Corporation

LXT6155LE Datasheet(HTML) 18 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

Datasheet Download

Link URL