| Electronic Components Datasheet Search |
|
PCF5001 Datasheet(PDF) 11 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCF5001 Datasheet(HTML) 11 Page - NXP Semiconductors |
|
11 / 44 page ![]() 1997 Mar 04 11 Philips Semiconductors Product specification POCSAG Paging Decoder PCF5001 7.3 Modes and states of the decoder The PCF5001 supports two basic operating modes: • ‘Alert-only pager’ mode • ‘Display pager’ mode. Two further modes, the programming mode and the test mode, are implemented to program and verify the EEPROM contents and to support pager production and approval tests, respectively. In ‘alert-only pager’ mode no external microcontroller is required, see Fig.22. A three position slider switch interface is provided to select the internal state of the decoder. The decoder performs regular scanning of the switch inputs to detect a status change. A push-button interface is provided on the SR input, which is used as input for user acknowledgment actions and status interrogation. Upon reception of valid calls, tone alert cadences are generated. A call storage is provided to store calls received while operating in SILENT status and to recall cadences upon ‘repeat’ mode operation. The voltage doubler and the frequency reference output are disabled in this mode. In ‘display pager’ mode the PCF5001 operates as decoder and pager controller in combination with an external microcontroller (see Fig.23). The internal states of the decoder are determined by appropriate logic levels on the status inputs. A bus type interface structure is used to interface the decoder to the microcontroller. The decoder's on-chip voltage converter provides doubled supply voltage output to provide a higher supply voltage to the microcontroller and any additional hardware. The logic levels of the interface's input and output signals are level shifted to allow for direct coupling between microcontroller and the decoder. Upon detection of a valid call, address and message information are transferred to the external microcontroller using the serial microcontroller interface. In addition, appropriate call alert cadences are generated. If the decoder is in one of the two operating modes, it is always in one of the following three internal states: • OFF status. This is the power saving, inactive status of the PCF5001. The paging receiver is disabled, no decoding of input data takes place. However, the crystal oscillator is kept running to ensure that scanning of the status inputs/status switch is maintained to allow changing into one of the following two active states. • ON status. This is the normal active status of the decoder. Incoming calls are compared with the user addresses stored in the internal EEPROM. Upon detection of valid calls, alert cadences and LED indication are generated and data is shifted out at the serial microcontroller interface. • SILENT status. The SILENT status is the same as the ON status with the exception that valid calls no longer cause generation of call alert cadences. Instead, if programmed as ‘alert-only pager’, the decoder stores up to eight different calls and generates appropriate alert cadences after the decoder has been put back into the ON status. However, special SILENT override calls will cause generation of alert cadences, if enabled. The decoder operating status is selected as indicated in Table 1. When programmed for ‘alert-only pager’ a switch debounce period is applied to the status inputs. For status change and status interrogation in ‘display pager’ mode, see Figs 6 and 7. Table 1 Truth table for decoder operating status Note 1. The EEPROM transfer mode applies to ‘display pager’ mode only. ON INPUT SK INPUT OPERATING STATUS 0 0 OFF 0 1 OFF (EEPROM transfer mode; note 1) 10 ON 1 1 SILENT |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |