ELM329LP datasheet(11/87 Pages) ELM

11 / 87 page

Several parameters within the ELM329 can be

adjusted in order to modify its behaviour. These do not

normally have to be changed before attempting to talk

to the vehicle, but occasionally the user may wish to

customize these settings – for example by turning the

character echo off, adjusting a timeout value, or

changing the header (ID) bytes. In order to do this,

internal ‘AT’ commands must be used.

Those familiar with PC modems will immediately

recognize AT commands as a standard way in which

modems are internally configured. The ELM329 uses

essentially the same method, always watching the

data sent by the PC, looking for messages that begin

with the character ‘A’ followed by the character ‘T’. If

found, the next characters will be interpreted as an

internal configuration or ‘AT’ command, and will be

executed upon receipt of a terminating carriage return

character. If the command is just a setting change, the

ELM329 will reply with the characters ‘OK’, to say that

it was successfully completed.

Some of the commands require that numbers be

provided as arguments, in order to set the internal

values. These will always be hexadecimal numbers

which must generally be provided in pairs. The

hexadecimal conversion chart in the OBD Commands

section (page 28) may be helpful if you wish to

interpret the values. Also, one should be aware that for

the on/off types of commands, the second character is

the number 1 or the number 0, the universal terms for

on and off.

The remainder of this page, and the next page

following provide a summary of all of the commands

that the current version of the ELM329 recognizes. A

more complete description of each command begins

on page 13.

11 of 87

ELM329L

ELM329L DSA

Elm Electronics – Circuits for the Hobbyist

www.elmelectronics.com

AT Command Summary

AT Commands

ELM329 Options

<CR>

repeat the last command

BRD hh

try Baud Rate Divisor hh

BRT hh

set Baud Rate Timeout

set all to Defaults

E0, E1

Echo off, or on*

print the version ID

L0, L1

Linefeeds off, or on

go to low power mode

M0, M1

Memory off, or on

Read the stored Data

SD hh

Save Data byte hh

Warm Start (quick software reset)

reset all

display the device description

display the device identifier

@3 cccccccccccc store the @2 identifier

Programmable Parameters

PP xx OFF

disable Prog Parameter xx

PP FF OFF

all Prog Parameters disabled

PP xx ON

enable Prog Parameter xx

PP FF ON

all Prog Parameters enabled

PP xx SV yy

for PP xx, Set the Value to yy

PPS

print a PP Summary

Voltage Readings

CV dddd

Calibrate the Voltage to dd.dd volts

CV 0000

restore CV value to factory setting

Read the input Voltage

Other

C0, C1

Control Output off*, or on

IGN

read the IgnMon input level

IN1

read INput 1 level

IN2

read INput 2 level

Note:

Settings shown with an asterisk (*)

are the default values

ELM329LP Datasheet(PDF) 11 Page - ELM Electronics

ELM329LP Datasheet(HTML) 11 Page - ELM Electronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87

Datasheet Download

Link URL