641 datasheet(67/106 Pages) INTEL

67 / 106 page

Datasheet

Land Listing and Signal Descriptions

DBI[3:0]#

Input/

Output

DBI[3:0]# (Data Bus Inversion) are source synchronous and

indicate the polarity of the D[63:0]# signals.The DBI[3:0]# signals

are activated when the data on the data bus is inverted. If more

than half the data bits, within a 16-bit group, would have been

asserted electrically low, the bus agent may invert the data bus

signals for that particular sub-phase for that 16-bit group.

DBR#

Output

DBR# (Debug Reset) is used only in processor systems where no

debug port is implemented on the system board. DBR# is used by

a debug port interposer so that an in-target probe can drive system

reset. If a debug port is implemented in the system, DBR# is a no

connect in the system. DBR# is not a processor signal.

DBSY#

Input/

Output

DBSY# (Data Bus Busy) is asserted by the agent responsible for

driving data on the processor FSB to indicate that the data bus is in

use. The data bus is released after DBSY# is de-asserted. This

signal must connect the appropriate pins/lands on all processor

FSB agents.

DEFER#

Input

DEFER# is asserted by an agent to indicate that a transaction

cannot be ensured in-order completion. Assertion of DEFER# is

normally the responsibility of the addressed memory or input/

output agent. This signal must connect the appropriate pins/lands

of all processor FSB agents.

DP[3:0]#

Input/

Output

DP[3:0]# (Data parity) provide parity protection for the D[63:0]#

signals. They are driven by the agent responsible for driving

D[63:0]#, and must connect the appropriate pins/lands of all

processor FSB agents.

DRDY#

Input/

Output

DRDY# (Data Ready) is asserted by the data driver on each data

transfer, indicating valid data on the data bus. In a multi-common

clock data transfer, DRDY# may be de-asserted to insert idle

clocks. This signal must connect the appropriate pins/lands of all

processor FSB agents.

DSTBN[3:0]#

Input/

Output

DSTBN[3:0]# are the data strobes used to latch in D[63:0]#.

Table 25.

Signal Description (Sheet 1 of 9)

Name

Type

Description

DBI[3:0] Assignment To Data Bus

Bus Signal

Data Bus Signals

DBI3#

D[63:48]#

DBI2#

D[47:32]#

DBI1#

D[31:16]#

DBI0#

D[15:0]#

Signals

Associated Strobe

D[15:0]#, DBI0#

DSTBN0#

D[31:16]#, DBI1#

DSTBN1#

D[47:32]#, DBI2#

DSTBN2#

D[63:48]#, DBI3#

DSTBN3#

641 Datasheet(PDF) 67 Page - Intel Corporation

641 Datasheet(HTML) 67 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL