| Electronic Components Datasheet Search |
|
TDF8599B Datasheet(PDF) 34 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
TDF8599B Datasheet(HTML) 34 Page - NXP Semiconductors |
|
34 / 54 page ![]() NXP Semiconductors TDF8599B I2C-bus controlled dual channel 43 W/2 Ohm, single channel 85 W/1 Ohm class-D power amplifier with load diagnostics TDF8599B All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved. Product data sheet Rev. 2 — 23 August 2016 34 / 54 VP (V) 8 24 20 16 12 (1) (2) 001aak227 90 30 60 120 150 Po (W) 0 (3) THD = 0.5 % RDSon = 0.1 Ω (at Tj = 100 °C), Rs = 0.025 Ω, tw(min) = 190 ns and IO(ocp) = 16 A (minimum). (1) RL = 1 Ω. (2) RL = 2 Ω. (3) RL = 4 Ω. Figure 28. Po as a function of VP in stereo mode with THD = 0.5 % VP (V) 8 24 20 16 12 (1) (3) 001aak228 60 120 180 30 90 150 Po (W) 0 (2) THD = 10 % RDSon = 0.1 Ω (at Tj = 100 °C), Rs = 0.025 Ω, tw(min) = 190 ns and IO(ocp) = 16 A (minimum). (1) RL = 1 Ω. (2) RL = 2 Ω. (3) RL = 4 Ω. Figure 29. Po as a function of VP in stereo mode with THD = 10 % 14.3 Output current limiting The peak output current is internally limited to 8 A maximum. During normal operation, the output current should not exceed this threshold level otherwise the output signal will be distorted. The peak output current can be estimated using Equation 6: (6) • Io = output current (A) • VP = supply voltage (V) • RL = load impedance (Ω) • RDSon = on-resistance of power switch (Ω) • Rs = series resistance of output inductor (Ω) Example: A 2 Ω speaker can be used with a supply voltage of 19 V before current limiting is triggered. Current limiting (clipping) avoids audio holes but can cause distortion similar to voltage clipping. In Parallel mode, the output current is internally limited above 16 A. 14.4 Speaker configuration and impedance A flat-frequency response (due to a 2nd order Butterworth filter) is obtained by changing the low-pass filter components (LLC, CLC) based on the speaker configuration and impedance. Table 22 shows the required values. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |