SC28L198 datasheet(27/56 Pages) PHILIPS

27 / 56 page

Philips Semiconductors

Product specification

SC28L198

Octal UART for 3.3V and 5V supply voltage

1999 Jan 14

Table 22. XISR – Xon–Xoff Interrupt Status Register

Bits 7:6

Bits 5:4

Bits 3:2

Bits 1:0

Received X Character Sta-

tus

Automatic X Character transmis-

sion status

TxD flow status

TxD character status

00 – none

01 – Xoff received

10 – Xon received

11 – both received

00 – none

01 – Xon transmitted

10 – Xoff transmitted

11 – Illegal, does not occur

00 – normal

01 – TxD halt pending

10 – re–enabled

11 – flow disabled

00 – normal TxD data

01 – wait on normal data

10 – Xoff in pending

11 – Xon in pending

XISR[7:6] – Received X Character Status. This field can be read to

determine if the receiver has encountered an Xon or Xoff character

in the incoming data stream. These bits are maintained until a read

of the XISR. The field is updated by X character reception

regardless of the state of MR0(7, 3:2) or IMR(4). The field can

therefore be used as a character detector for the bit patterns stored

in the Xon and Xoff Character Registers.

XISR[5:4] – Automatic transmission Status. This field indicates the

last flow control character sent in the Auto Receiver flow control

mode. If Auto Receiver mode has not been enabled, this field will

always read b’00. It will likewise reset to b’00 if MR0(3) is reset. If

the Auto Receiver mode is exited while this field reads b’10, it is the

user’s responsibility to transmit an Xon, when appropriate.

XISR[3:2] – TxD flow Status. This field tracks the transmitter’s flow

status as follows:

00 – normal. The flow control is under host control.

01 – TxD halt pending. After the current character finishes the

transmitter will stop. The status will then change to b’00.

10 – re–enabled. The transmitter had been halted and restarted.

It is sending data characters. After a read of the XISR, it will

return to ”normal” status.

11 – disabled. The transmitter is flow controlled.

XISR[1:0] – TxD character Status. This field allows determination of

the type of character being transmitted. If XISR(1:0) is b’01, the

channel is waiting for a data character to transfer from the TxFIFO.

This condition will only occur for a bit time after an Xon or Xoff

character transmission unless the TxFIFO is empty.

Table 23. WDTRCR – Watch-dog Timer Enable

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

WDT

1 on

0 off

1 on

0 off

1 on

0 off

1 on

0 off

1 on

0 off

1 on

0 off

1 on

0 off

1 on

0 off

This register enables the watch-dog Timer for each of the 8

receivers on the Octal UART.

Table 24. BRGTRU

– BRG Timer Reload

Registers, Upper

Bits 7:0

8 MSB of the BRG Timer divisor.

This is the upper byte of the 16 bit value used by the BRG timer in

generating a baud rate clock

Table 25. BRGTRL

– BRG Timer Reload

Registers, Lower

Bits 7:0

8 LSB of the BRG Timer divisor.

This is the lower byte of the 16 bit value used by the BRG timer in

generating a baud rate clock.

Table 26. BRGTCR – BRG Timer Control Register (BRGTCR)

Bit 7

Bit 6:4

Bit 3

Bit 2:0

BRGTCR b, Register control

BRGTCR b, Clock selection

BRGTCR a, Register control

BRGTCR a, Clock selection

0 – Resets the timer register and

holds it stopped

1 – Allows the timer register to

run.

000 – Sclk / 16

001 – Sclk / 32

010 – Sclk/ 64

011 – Sclk / 128

100 – X1

101 – X1 / 2

110 – I/O1b

111 – GIN(1)

0 – Resets the timer register and

holds it stopped.

1 – Allows the timer register to

run.

000 – Sclk / 16

001 – Sclk / 32

010 – Sclk / 64

011 – Sclk / 128

100 – X1

101 – X1 / 2

110 – I/O1a

111 – GIN(0)

Start/Stop control and clock select register for the two BRG

counters. The clock selection is for the input to the counters. It is

that clock divided by the number represented by the BRGTU and

BRGTL the will be used as the 16x clock for the receivers and

transmitters. When the BRG timer Clock is selected for the

receiver(s) or transmitter(s) the receivers and transmitters will

consider it as a 16x clock and further device it by 16. In other words

the receivers and transmitters will always be in the 16x ode of

operation when the internal BRG timer is selected for their clock.

SC28L198 Datasheet(PDF) 27 Page - NXP Semiconductors

SC28L198 Datasheet(HTML) 27 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Datasheet Download

Link URL