SC3200 datasheet(173/447 Pages) AMD

173 / 447 page

AMD Geode™ SC3200 Processor Data Book

173

Core Logic Module

Revision 5.1

6.2.7.1

I/O Port 092h System Control

I/O Port 092h allows for a fast keyboard assertion of an

A20# SMI and a fast keyboard CPU reset. Decoding for this

The assertion of a fast keyboard A20# SMI is controlled by

either I/O Port 092h or by monitoring for the keyboard com-

mand sequence (see Section 6.2.8.1 "Fast Keyboard Gate

Address 20 and CPU Reset" on page 173). If bit 1 of I/O

Port 092h is cleared, the Core Logic module internally

asserts an

A20M#, which in turn causes an SMI to the

GX1 module. If bit 1 is set, A20M# is internally de-

asserted, again causing an SMI.

The assertion of a fast keyboard reset (WM_RST SMI) is

controlled by bit 0 in I/O Port 092h or by monitoring for the

keyboard command sequence (write data = FEh to I/O port

64h). If bit 0 is changed from 0 to 1, the Core Logic module

generates a reset to the GX1 module by generating a

WM_RST SMI. When the WM_RST SMI occurs, the BIOS

jumps to the Warm Reset vector. Note that Warm Reset is

not a pin, it is under SMI control.

6.2.7.2

I/O Port 061h System Control

Through I/O Port 061h, the speaker output can be enabled,

the status of IOCHK# and SERR# can be read, and the

state of the speaker data (Timer2 output) and refresh tog-

gle (Timer1 output) can be read back. Note that NMI is

under SMI control. Even though the hardware is present,

the IOCHK# ball does not exist. Therefore, an NMI from

IOCHK# can not happen.

6.2.7.3

SMI Generation for NMI

Figure 6-10 shows how the Core Logic module can gener-

ate an SMI for an NMI. Note that NMI is not a ball.

6.2.8

Keyboard Support

The Core Logic module can actively decode the keyboard

controller I/O Ports 060h, 062h, 064h and 066h, and gener-

ate an LPC bus cycle. Keyboard positive decoding can be

disabled if F0 Index 5Ah[1] is cleared (i.e., subtractive

decoding enabled).

6.2.8.1

Fast Keyboard Gate Address 20 and CPU

Reset

The Core Logic module monitors the keyboard I/O Ports

064h and 060h for the fast keyboard A20M# and CPU reset

control sequences. If a write to I/O Port 060h[1] = 1 after a

write takes place to I/O Port 064h with data of D1h, then

the Core Logic module asserts the A20M# signal. A20M#

remains asserted until cleared by any one of the following:

• A write to bit 1 of I/O Port 092h.

• A CPU reset of some kind.

• A write to I/O Port 060h[1] = 0 following a write to I/O

Port 064h with data of D1h.

The fast keyboard A20M# and CPU reset can be disabled

through F0 Index 52h[7]. By default, bit 7 is set, and the

fast keyboard A20M# and CPU reset monitor logic is

active. If bit 7 is clear, the Core Logic module forwards the

commands to the keyboard controller.

By default, the Core Logic module forces the de-assertion

of A20M# during a warm reset. This action may be dis-

abled if F0 Index 52h[4] is cleared.

Figure 6-10. SMI Generation for NMI

PERR#

IOCHK#

F0 Index 04h[6]

SERR#

F0 Index 04h[8]

F0 Index 40h[1]

I/O Port 061h[2]

I/O Port 061h[3]

I/O Port 070h[7]

Parity Errors

AND

System Errors

NMI

SMI

F0 Index 04h: PCI Command Register

Bit 6 = PE (PERR# Enable)

Bit 8 = SE (SERR# Enable)

F0 Index 40h: PCI Function Control Register 1

Bit 1 = PES (PERR# Signals SERR#)

I/O Port 061h: Port B

Bit 2 = ERR_EN (PERR#/SERR# Enable)

Bit 3 = IOCHK_EN (IOCHK Enable)

AND

I/O Port 070h: RTC Index Register (WO)

Bit 72 = NMI (NMI Enable)

NMI

(No External Connection)

SC3200 Datasheet(PDF) 173 Page - Advanced Micro Devices

SC3200 Datasheet(HTML) 173 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL