SC3200 datasheet(308/447 Pages) AMD

308 / 447 page

308

AMD Geode™ SC3200 Processor Data Book

Core Logic Module - USB Controller Registers - PCIUSB

Revision 5.1

Offset 54h-57h

HcRhPortStatus[1] Register (R/W)

Reset Value = 00000000h

31:21

Reserved. Read/Write 0s.

PortResetStatusChange. This bit indicates that the port reset signal has completed.

0: Port reset is not complete.

1: Port reset is complete.

PortOverCurrentIndicatorChange. This bit is set when OverCurrentIndicator changes. Writing a 1 clears this bit. Writing

a 0 has no effect.

PortSuspendStatusChange. This bit indicates the completion of the selective resume sequence for the port.

0: Port is not resumed.

1: Port resume is complete.

PortEnableStatusChange. This bit indicates that the port has been disabled due to a hardware event (cleared PortEna-

bleStatus).

0: Port has not been disabled.

1: PortEnableStatus has been cleared.

ConnectStatusChange. This bit indicates a connect or disconnect event has been detected. Writing a 1 clears this bit.

Writing a 0 has no effect.

0: No connect/disconnect event.

1: Hardware detection of connect/disconnect event.

If DeviceRemoveable is set, this bit resets to 1.

15:10

Reserved. Read/Write 0s.

Read: LowSpeedDeviceAttached. This bit defines the speed (and bud idle) of the attached device. It is only valid when

CurrentConnectStatus is set.

0: Full Speed device.

1: Low Speed device.

Write: ClearPortPower. Writing a 1 clears PortPowerStatus. Writing a 0 has no effect.

Read: PortPowerStatus. This bit reflects the power state of the port regardless of the power switching mode.

0: Port power is off.

1: Port power is on.

If NoPowerSwitching is set, this bit is always read as 1.

Write: SetPortPower. Writing a 1 sets PortPowerStatus. Writing a 0 has no effect.

7:5

Reserved. Read/Write 0s.

Read: PortResetStatus.

0: Port reset signal is not active.

1: Port reset signal is active.

Write: SetPortReset. Writing a 1 sets PortResetStatus. Writing a 0 has no effect.

Read: PortOverCurrentIndicator. This bit reflects the state of the OVRCUR pin dedicated to this port. This field is only

valid if NoOverCurrentProtection is cleared and OverCurrentProtectionMode is set.

0: No over-current condition.

1: Over-current condition.

Write: ClearPortSuspend. Writing a 1 initiates the selective resume sequence for the port. Writing a 0 has no effect.

Read: PortSuspendStatus.

0: Port is not suspended.

1: Port is selectively suspended.

Write: SetPortSuspend. Writing a 1 sets PortSuspendStatus. Writing a 0 has no effect.

Table 6-42. USB_BAR+Memory Offset: USB Controller Registers (Continued)

Bit

Description

SC3200 Datasheet(PDF) 308 Page - Advanced Micro Devices

SC3200 Datasheet(HTML) 308 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL