SC3200 datasheet(334/447 Pages) AMD

334 / 447 page

334

AMD Geode™ SC3200 Processor Data Book

Video Processor Module

Revision 5.1

Field Interrupt.

When the field interrupt occurs on the completion of an

odd field, the interrupt must program the Video Data

Odd Base Address with the other buffer’s address. The

odd field will ping-pong between the two buffers. When

the interrupt is due to the completion of an even field,

the interrupt handler must program the GX1 module’s

video buffer start offset value (GX_BASE+Memory

Offset 8320h) with the address of the frame (both odd

and even fields) that was just received from the VIP

block. This new address will not take affect until the

start of a new frame. It must also program the Video

Data Even Base Address with the other buffer so that

the even field will ping-pong just like the odd field. The

field just received can be known by reading the Cur-

rent Field bit (F4BAR2+Memory Offset 08h[24]).

7.2.1.3

Capture VBI Mode

There are three types of VBI data defined by the CCIR-656

protocol: Task A data, Task B data, and Ancillary data. The

VIP block supports the capture for each data type. Gener-

ally Task A data is the data type captured. Just as in Cap-

ture Video mode, there are three registers that tell the bus

master where to put the raw VBI data in the GX1 module’s

frame buffer. Once the raw VBI data has been captured,

the data can be manipulated or decoded. The data can

also be used by an application. An example of this would

be an Internet address that is encoded on one or more of

the VBI lines, or have an application decode the Closed

Captioning information put in the graphics frame buffer.

The registers, F4BAR2+Memory Offset 40h, 44h, and 48h,

tell the bus master the destination addresses for the VBI

data in the GX1 module’s frame buffer. Five bits

(F4BAR2+Memory Offset 00h[21:17]) are used to tell the

bus master the data types to store. Capture VBI mode

needs

enabled

F4BAR2+Memory

Offset

04h[9,1:0]. The Field Interrupt bit (F4BAR2+Memory Offset

04h[16]) should be used by the software driver to know

when the captured VBI data has been completed for a field.

Figure 7-6. Capture Video Mode Weave Example Using Two Video Frame Buffers

Video Data Odd Base

F4BAR2+Memory Offset 20h

Video Data Even Base

F4BAR2+Memory Offset 20h

VID_START_OFFSET

GX_BASE+Memory Offset 8320h

Ping-pongs between the

two buffers during runtime

GX1 Module’s Video Frame Buffer

456789

1234

6789 10 11 12 13 14 15 16 17 18 19 20

Capture video fill sequence

GX1 Module’s Display

Video Data Even Base

F4BAR2+Memory Offset 24h

Video Data Even Base

F4BAR2+Memory Offset 24h

Odd and Even fields are

Buf #2

Video Frame Buffer #1

Video Frame Buffer #2

Line 1 Odd Field

Line n Odd Field

Line 2 Odd Field

Line 1 Even Field

Line 2 Even Field

Line n-1 Odd Field

Line n-1 Even Field

Line n Odd Field

Line n Even Field

Line 1 Odd Field

Line 1 Even Field

Line 2 Odd Field

Line 2 Even Field

Line n-1 Odd Field

Line n-1 Even Field

Line n Even Field

85 frames per second

30 frames per second

Buf #1

Controller empty sequence

“Weaved” together

Ping-pongs between the two buffers during runtime

SC3200 Datasheet(PDF) 334 Page - Advanced Micro Devices

SC3200 Datasheet(HTML) 334 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL