SC3200 datasheet(263/447 Pages) AMD

263 / 447 page

AMD Geode™ SC3200 Processor Data Book

263

Core Logic Module - SMI Status and ACPI Registers - Function 1

Revision 5.1

6.4.2.2

ACPI Support Registers

F1 Index 40h, Base Address Register 1 (F1BAR1), points

to the base address of where the ACPI Support registers

are located. Table 6-34 shows the I/O mapped ACPI Sup-

port registers accessed through F1BAR1.

Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers

Bit

Description

Offset 00h-03h

P_CNT — Processor Control Register (R/W)

Reset Value: 00000000h

31:5

Reserved. Always reads 0.

THT_EN (Throttle Enable). When this bit is asserted, it enables throttling of the clock based on the CLK_VAL field (bits

[2:0] of this register).

Disable.

Enable.

If F1BAR1+I/O Offset 18h[8] =1, an SMI is generated when this bit is set.

Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].

Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[1].

Reserved. Always reads 0.

2:0

CLK_VAL (Clock Throttling Value). CPU duty cycle:

000: Reserved

010: 25%

100: 50%

110: 75%

001: 12.5%

011: 37.5%

101: 62.5%

111: 87.5%

Offset 04h

Reserved

Reset Value: 00h

Note:

This register should not be read. It controls a reserved function of power management logic.

Offset 05h

P_LVL3 — Enter C3 Power State Register (RO)

Reset Value: xxh

7:0

P_LVL3 (Power Level 3). Reading this 8-bit read only register causes the processor to enter the C3 power state. Reads of

P_LVL3 return 0. Writes have no effect.

The ACPI state machine always waits for an SMI (any SMI) to be generated and serviced before transfer into C3 power

state.

A read of this register causes an SMI if enabled: F1BAR1+I/O Offset 18h[11] = 1 (default).

Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].

Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[4].

Offset 06h

SMI_CMD — OS/BIOS Requests Register (R/W)

Reset Value: 00h

7:0

SMI_CMD (SMI Command and OS / BIOS Requests). A write to this register stores data and a read returns the last data

written. In addition, a write to this register always generates an SMI. A read of this register does not generate an SMI.

Top level SMI status is reported at F1BAR0+I/O Offset 00h/02h[2].

Second level SMI status is reported at F1BAR0+I/O Offset 20h/22h[0].

Offset 07h

ACPI_FUN_CNT — ACPI Function Control Register (R/W)

Reset Value: 00h

7:6

LED_CNT (LED Output Control). Controls the blinking of an LED when in the SL4 or SL5 sleep state

00: Disable (LED# signal, is HiZ).

01: Zero (LED# signal is HiZ).

10: Blink @ 1 Hz rate, when in SL4 and SL5 sleep states. Duty cycle: LED# is 10% pulled low, 90% HiZ.

11: One (LED# is pulled low, when in SL4 and SL5 sleep states)

Reserved. Must be set to 0.

INTR_WU_SL1. Enables wakeup on enabled interrupts in sleep state SL1.

0: Disable wakeup from SL1, when an enabled interrupt is active.

1: Enable wakeup from SL1, when an enabled interrupt is active.

GPWIO_DBNC_DIS (GPWIO0 and GPWIO1 Debounce). When enabled, a high-to-low or low-to-high transition of greater

than 15.8 ms is required for GPWIO0 and GPWIO1 to be recognized.

0: Enable. (Default)

1: Disable. (No debounce)

GPWIO2 pin does not have debounce capability.

2:1

Reserved. Must be set to 0.

SC3200 Datasheet(PDF) 263 Page - Advanced Micro Devices

SC3200 Datasheet(HTML) 263 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL