TMS320DM355 datasheet(82/153 Pages) TI

82 / 153 page

www.ti.com

3.11.4 ARM Boot Mode Configuration

3.11.5 AEMIF Configuration

3.12 Device Boot Modes

TMS320DM355

Digital Media System-on-Chip (DMSoC)

SPRS463 – SEPTEMBER 2007

Table 3-16. Module Configuration (continued)

Default States

ARM

AlwaysOn

Enable

BUS

AlwaysOn

Enable

BUS

AlwaysOn

Enable

BUS

AlwaysOn

Enable

BUS

AlwaysOn

Enable

BUS

AlwaysOn

Enable

BUS

AlwaysOn

Enable

BUS

AlwaysOn

Enable

Reserved

VPSS DAC

Always On

SyncRst

The input pins BTSEL[1:0] determine whether the ARM will boot from its ROM or from the Asynchronous

EMIF (AEMIF). When ROM boot is selected (BTSEL[1:0] = 00, 10, or 11), a jump to the start of internal

ROM (address 0x0000: 8000) is forced into the first fetched instruction word. The embedded ROM boot

loader code (RBL) then performs certain configuration steps, reads the BOOTCFG register to determine

the desired boot method, and branches to the appropriate boot routine (i.e., a NAND, MMC/SD, or UART

loader routine).

If AEMIF boot is selected (BTSEL[1:0] = 01), a jump to the start of AEMIF (address 0x0200: 0000) is

forced into the first fetched instruction word. The ARM then continues executing from external

asynchronous memory using the default AEMIF timings until modified by software.

NOTE

For AEMIF boot, the OneNAND must be connected to the first AEMIF chip select space

(EM_CE0). Also, the AEMIF does not support direct execution from NAND Flash.

Boot modes are further described in Section 3.12.

3.11.5.1 AEMIF Pin Configuration

The input pins AECFG[3:0] determine the AEMIF configuration immediately after reset. Use AECFG[3:0]

to properly configure the pins of the AEMIF. Refer to the section on pin multiplexing in Section 3.9.

Also, see the Asynchronous External Memory Interface (AEMIF) Peripheral Reference Guide (SPRUEE8)

for more information on the AEMIF.

3.11.5.2 AEMIF Timing Configuration

When AEMIF is enabled, the wait state registers are reset to the slowest possible configuration, which is

88 cycles per access (16 cycles of setup, 64 cycles of strobe, and 8 cycles of hold). Thus, with a 24 MHz

clock at MXI, the AEMIF is configured to run at 6 MHz/88 which equals approximately 68 kHz by default.

See the Asynchronous External Memory Interface (AEMIF) Peripheral Reference Guide for more

information on the AEMIF.

The DM355 ARM can boot from either Async EMIF (AEMIF/OneNand) or from ARM ROM, as determined

by the setting of the device configuration pins BTSEL[1:0]. The BTSEL[1:0] pins can define the ROM boot

mode further as well.

Detailed Device Description

Submit Documentation Feedback

TMS320DM355 Datasheet(PDF) 82 Page - Texas Instruments

TMS320DM355 Datasheet(HTML) 82 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL