LPC4370 datasheet(13/150 Pages) NXP

13 / 150 page

LPC4370

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 2 — 21 October 2013

13 of 150

NXP Semiconductors

LPC4370

32-bit ARM Cortex-M4/M0 microcontroller

P1_18

N12

J10

[3]

I; PU I/O

GPIO0[13] — General purpose digital input/output pin.

I/O

U2_DIR — RS-485/EIA-485 output enable/direction control for USART2.

R — Function reserved.

ENET_TXD0 — Ethernet transmit data 0 (RMII/MII interface).

T0_MAT3 — Match output 3 of timer 0.

CAN1_RD — CAN1 receiver input.

I/O

SGPIO12 — General purpose digital input/output pin.

R — Function reserved.

P1_19

M11

[3]

I; PU I

ENET_TX_CLK (ENET_REF_CLK) — Ethernet Transmit Clock (MII

interface) or Ethernet Reference Clock (RMII interface).

I/O

SSP1_SCK — Serial clock for SSP1.

R — Function reserved.

CLKOUT — Clock output pin.

R — Function reserved.

I2S0_RX_MCLK — I2S receive master clock.

I/O

I2S1_TX_SCK — Transmit Clock. It is driven by the master and received by

the slave. Corresponds to the signal SCK in the I2S-bus specification.

P1_20

M10

K10

[3]

I; PU I/O

GPIO0[15] — General purpose digital input/output pin.

I/O

SSP1_SSEL — Slave Select for SSP1.

R — Function reserved.

ENET_TXD1 — Ethernet transmit data 1 (RMII/MII interface).

T0_CAP2 — Capture input 2 of timer 0.

R — Function reserved.

I/O

SGPIO13 — General purpose digital input/output pin.

R — Function reserved.

P2_0

T16

G10 [3]

I; PU I/O

SGPIO4 — General purpose digital input/output pin.

U0_TXD — Transmitter output for USART0.

I/O

EMC_A13 — External memory address line 13.

USB0_PPWR — VBUS drive signal (towards external charge pump or

power management unit); indicates that VBUS must be driven (active HIGH).

Add a pull-down resistor to disable the power switch at reset. This signal has

opposite polarity compared to the USB_PPWR used on other NXP LPC

parts.

I/O

GPIO5[0] — General purpose digital input/output pin.

R — Function reserved.

T3_CAP0 — Capture input 0 of timer 3.

ENET_MDC — Ethernet MIIM clock.

Table 3.

Pin description …continued

LCD, Ethernet, USB0, and USB1 functions are not available on all parts. See Table 2.

Symbol

Description

LPC4370 Datasheet(PDF) 13 Page - NXP Semiconductors

LPC4370 Datasheet(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL