Electronic Components Datasheet Search
  English  ▼

X  

AD1803 Datasheet(PDF) 5 Page - Analog Devices

Part # AD1803
Description  Modem/Telephony Codec
PDF  32 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD1803 Datasheet(HTML) 5 Page - Analog Devices

  AD1803 Datasheet HTML 1Page - Analog Devices AD1803 Datasheet HTML 2Page - Analog Devices AD1803 Datasheet HTML 3Page - Analog Devices AD1803 Datasheet HTML 4Page - Analog Devices AD1803 Datasheet HTML 5Page - Analog Devices AD1803 Datasheet HTML 6Page - Analog Devices AD1803 Datasheet HTML 7Page - Analog Devices AD1803 Datasheet HTML 8Page - Analog Devices AD1803 Datasheet HTML 9Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 32 page
background image
AD1803
TYPICAL SUPPLY CURRENT
Typical supply current is for most common modes of operation. All currents in mA, unless otherwise noted.
Table 2.
Resource
3.3 V
5.0 V
Register Writes to Enter Mode
GPIO Weak Pull-Up Current per Pin
RESET is Asserted
XTALI Off (All Down)1
XTALI Enabled: Nominal Power
XTALI Enabled: Low Power
CLK_OUT Pin Running2
RESET is Deasserted and Analog and Digital Codec
in Full Power Mode
SPORT and CLK_OUT Active2, 3
XTALI in Low Power Mode2, 3
CLK_OUT Inactive (Low)3
VREF Powered Up3
ADC Enabled
DAC Enabled3, 5
ADC + DAC Enabled3, 5
ADC, DAC, + MON Enabled3, 4, 5
ADC, DAC, + MON Enabled3, 5, 6
~100
<30.0
1.4
1.0
1.6
2.6
2.2
1.7
1.9
7.3
8.2
9.2
9.3
10.2
~140 μA
<40.0 μA
2.4
1.7
3.2
6.4
5.7
4.3
4.5
12.4
13.7
14.7
14.9
16.3
Default settings after power-on RESET
Default settings after power-on RESET
5C:R34P4 = 1
5C:R34P4 = 1, 64b1:XTLP = 1
5C:CLKEA = 1
Default settings after power-on RESET
64b1:XTLP = 1
5C:CLKED = 0
3E:VPDN = 0
3E:APDN = 0
3E:DPDN = 0
3E:APDN = DPDN = 0
3E:APDN = DPDN = 0, 5E:GPMON = 1
3E:APDN = DPDN = 0, 5E:GPMON = 1
1 Assumes all inputs are static (not switching) and all output loads are capacitive (nonresistive).
2 Excludes current drawn by CLK_OUT pin board loading.
3 Assumes the serial interface is configured in AC '97 primary mode with 20 pF loads on the SDATA_IN pin and BIT_CLK pin. Typical current is approximately 0.8 mA less if the
serial interface is configured in DSP mode with 20 pF loads on the SYNC pin, BIT_CLK pin, and SDATA_IN pin (due to a lower BIT_CLK frequency).
4 Assumes a 20 pF load on the G[4]/MOUT pin.
5 Assumes no DAC load, 0.6 mA should be added if a 600 Ω load is used.
6 Assumes the G[4]/MOUT pin is loaded with a 1 kΩ resistor in series with a parallel 4.7 kΩ resistor and 100 nF capacitor combination tied to digital ground. This filter, with the
output taken from the middle node, has a 1500 Hz corner to filter out high-frequency Σ-Δ noise. It generates an approximate 1 V p-p output when using a 5 V digital supply
with the monitor output configured as first order (Bit MMD1 and Bit MMD0 set to 10 in Register 0x60 Bank 2) if the filter output load is greater than or equal to 20 kΩ.
Rev. A | Page 5 of 32



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com