DIX9211 datasheet(13/110 Pages) TI2

13 / 110 page

RST

MODE

Tied to V

or DGND

= 2.2 V typ

= 3.3 V typ

0 V

RSTL

DIX9211

www.ti.com

SBAS519 – SEPTEMBER 2010

DIX9211 MODULE DESCRIPTIONS

Power Supply

The DIX9211 has three power-supply pins and three ground pins. All ground pins (AGND, DGND, and GNDRX)

must be connected as closely as possible to the DIX9211. The DIX9211 DVDD and DGND pins are

power-supply pins that support all the onboard digital circuitry for the DIX9211. DVDD should be connected to a

3.3-V supply. DVDD drives the internal power-on reset circuit, making it a startup requirement.

VCC and AGND are analog power-supply power pins that support the DIR analog supply rails.

VDDRX is a dedicated power supply for the coaxial input amplifiers on pins RXIN0 and RXIN1. It should be

connected to a 3.3-V pin. The relative GND pin for this supply is GNDRX. If the coaxial amplifiers are not used

(for example, the application only uses optical inputs), then no power supply is required for the VDDRX.

Because VCC (3.3 V) is an analog supply (used as part of the power supply for the DIR PLL), care should be

taken to ensure minimum noise and ripple are present. 0.1-mF ceramic capacitors and 10-mF electrolytic

capacitors should be used to decouple each supply pin to the respective relative GND.

Power-Down Function

The DIX9211 has a power-down function that is controlled by the external RST pin or a power control register.

When the RST pin is held at GND, the DIX9211 powers down.

When the device is powered down (that is, RST = GND), all register values are cleared and reset to the

respective default values. By default, all modules are powered on except for the coaxial amplifier.

The other option for powering down the device is to use the Power Control Register (Register 40h). The Power

Control Register allows selective power down of the DIR, DIT, Coax Amp, and Oscillator circuit without resetting

other registers to the respective default modes.

The advantage of using the registers to power down individual modules of the DIX9211 is that the registers retain

the respective settings rather than resetting to default.

System Reset

The DIX9211 has two sources for reset: the internal power-on reset circuit (hereafter called POR) and the

external reset circuit. Initialization (reset) is done automatically when VDD exceeds 2.2 V (typ).

When only the onboard POR is to be used, the RST pin should be connected to VDD directly. An external pull-up

resistor should not be used, because the RST pin has an internal pull-down resistor (typ 50 k

Ω). If an external

resistor is used, then the reset is not released. The reset sequence is shown in Figure 1.

Figure 1. Required System Reset Timing

Submit Documentation Feedback

Product Folder Link(s): DIX9211

DIX9211 Datasheet(PDF) 13 Page - Texas Instruments

DIX9211 Datasheet(HTML) 13 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL