AM79C976 datasheet(25/309 Pages) AMD

25 / 309 page

8/01/00

Am79C976

P R E L I M INARY

By default INTA is an open-drain output. For applica-

tions that need an active-high edge-sensitive interrupt

signal, the INTA pin can be configured for this mode by

setting INTLEVEL (CMD3, bit 13 or BCR2, bit 7) to 1.

IRDY

Initiator Ready

Input/Output

IRDY indicates the ability of the initiator of the transac-

tion to complete the current data phase. IRDY is used

in conjunction with TRDY. Wait states are inserted until

both IRDY and TRDY are asserted simultaneously. A

data phase is completed on any clock when both IRDY

and TRDY are asserted.

When the Am79C976 controller is a bus master, it as-

serts IRDY during all write data phases to indicate that

valid data is present on AD[31:0]. During all read data

phases, the device asserts IRDY to indicate that it is

ready to accept the data.

When the Am79C976 controller is the target of a trans-

action, it checks IRDY during all write data phases to

determine if valid data is present on AD[31:0]. During

all read data phases, the device checks IRDY to deter-

mine if the initiator is ready to accept the data.

PAR

Parity

Input/Output

Parity is even parity across AD[31:0] and C/BE[3:0].

When the Am79C976 controller is a bus master, it gen-

erates parity during the address and write data phases.

It checks parity during read data phases. When the

Am79C976 controller operates in slave mode, it checks

parity during every address phase. When it is the target

of a cycle, it checks parity during write data phases and

it generates parity during read data phases.

PERR

Parity Error

Input/Output

During any slave write transaction and any master read

transaction, the Am79C976 controller asserts PERR

when it detects a data parity error and reporting of the

error is enabled by setting PERREN (PCI Command

the Am79C976 controller monitors PERR to see if the

target reports a data parity error.

REQ

Bus Request

Input/Output

The Am79C976 controller asserts REQ pin as a signal

that it wishes to become a bus master. REQ is driven

high when the Am79C976 controller does not request

the bus.

RST

Reset

Input

When RST is asserted LOW and the PG pin is HIGH,

then the Am79C976 controller performs an internal

syste m

r e set

t he

t y p e

H _ R ESET

(HARDWARE_RESET, see section on RESET). Imme-

diately after the initial power up, RST must be held low

for 26µs. At any other time RST must be held low for a

minimum of 30 clock periods to guarantee that the de-

vice is properly reset. While in the H_RESET state, the

Am79C976 controller will disable or deassert all out-

puts. RST may be asynchronous to clock when as-

serted or deasserted.

Asserting RST disables all of the PCI pins except the

PME pin.

SERR

System Error

Output

During any slave transaction, the Am79C976 controller

asserts SERR when it detects an address parity error,

and reporting of the error is enabled by setting PER-

REN (PCI Command register, bit 6) and SERREN (PCI

Command register, bit 8) to 1.

By default SERR is an open-drain output. For compo-

nent test, it can be programmed to be an active-high

totem-pole output.

STOP

Stop

Input/Output

In slave mode, the Am79C976 controller drives the

STOP signal to inform the bus master to stop the cur-

rent transaction. In bus master mode, the Am79C976

controller checks STOP to determine if the target wants

to disconnect the current transaction.

TRDY

Target Ready

Input/Output

TRDY indicates the ability of the target of the transac-

tion to complete the current data phase. Wait states are

inserted until both IRDY and TRDY are asserted simul-

taneously. A data phase is completed on any clock

when both IRDY and TRDY are asserted.

When the Am79C976 controller is a bus master, it

checks TRDY during all read data phases to determine

if valid data is present on AD[31:0]. During all write data

phases, the device checks TRDY to determine if the

target is ready to accept the data.

When the Am79C976 controller is the target of a trans-

action, it asserts TRDY during all read data phases to

indicate that valid data is present on AD[31:0]. During

all write data phases, the device asserts TRDY to indi-

cate that it is ready to accept the data.

AM79C976 Datasheet(PDF) 25 Page - Advanced Micro Devices

AM79C976 Datasheet(HTML) 25 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL