 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TAS5548DCAR Datasheet(PDF) 47 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TAS5548DCAR Datasheet(HTML) 47 Page - Texas Instruments |
|
|
47 / 116 page  TAS5548 www.ti.com SLES270A – NOVEMBER 2012 – REVISED APRIL 2015 Table 13. Audio System Configuration (General Control Register 0xE0) Audio System D31–D4 D3 D2 D1 D0 6 channels or 5.1 not using PSVC 0 0 0 1 X 6 channels using PSVC 0 0 1 1 X 5.1 system using PSVC 0 0 1 1 X 8 channels or 7.1 not using PSVC (default) 0 0 0 0 X 8 channels using PSVC 0 0 1 0 X 7.1 system using PSVC 0 0 1 0 X 7.4.21.3.1 Using Line Outputs in 6-Channel Configurations The audio system can be configured for a 6-channel configuration (with 2 lineouts) by writing a 1 to bit D1 of register 0xE0 (general control register). In this configuration, channel-5 and -6 processing are exactly the same as the other channels, except that the master volume and the loudness function have no effect on the signal. Note that in 6-channel configuration, channels 5 and 6 are unaffected by back-end error (BKND_ERR goes low). To use channels 5 and 6 as unprocessed lineouts, the following setup is recommended: • Channel-5 volume and channel-6 volume should be set for a constant output, such as 0 dB. • Bass and treble for channels 5 and 6 can be used if desired. • DRC1 should be bypassed for channels 5 and 6. • If a downmix is desired on channels 5 and 6 as lineout, the downmixing can be performed using the channel- 5 and channel-6 input mixers. • The operation of the channel-5 and -6 biquads is unaffected by the 6-/8-channel configuration setting. 7.4.21.4 Recovery from Clock Error The TAS5548 can be set either to perform a volume ramp up during the recovery sequence of a clock error or simply to come up in the last state (or desired state if a volume or tone update was in progress). This feature is enabled via I2C system control register 0x03. 7.4.21.5 Power-Supply Volume-Control Enable The power-supply volume control (PSVC) can be enabled and disabled via I2C register 0xE0. The subwoofer PWM output is always controlled by the PSVC. When using PSVC the subwoofer cannot be used as lineout. 7.4.21.6 Volume and Mute Update Rate The TAS5548 has fixed soft volume and mute ramp durations. The ramps are linear. The soft volume and mute ramp rates are adjustable by programming the I2C register 0xD0 for the appropriate number of steps to be 512, 1024, or 2048. The update is performed at a fixed rate regardless of the sample rate. • In normal speed, the update rate is 1 step every 4/fS seconds. • In double speed, the update is 1 step every 8/fS seconds. • In quad speed, the update is 1 step every 16/fS seconds. Because of processor loading, the update rate can increase for some increments by one step every 1/fS to 3/fS. However, the variance of the total time to go from 18 dB to mute is less than 25%. Table 14. Volume Ramp Periods in ms SAMPLE RATE (kHz) NUMBER OF STEPS 44.1, 88.2, 176.4 32, 48, 96, 192 512 46.44 42.67 1024 92.88 85.33 2048 185.76 170.67 Copyright © 2012–2015, Texas Instruments Incorporated Submit Documentation Feedback 47 Product Folder Links: TAS5548 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
