Electronic Components Datasheet Search
  English  ▼

X  

AD9554BCPZ Datasheet(PDF) 46 Page - Analog Devices

Part # AD9554BCPZ
Description  Quad PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator
PDF  116 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD9554BCPZ Datasheet(HTML) 46 Page - Analog Devices

Back Button AD9554BCPZ Datasheet HTML 42Page - Analog Devices AD9554BCPZ Datasheet HTML 43Page - Analog Devices AD9554BCPZ Datasheet HTML 44Page - Analog Devices AD9554BCPZ Datasheet HTML 45Page - Analog Devices AD9554BCPZ Datasheet HTML 46Page - Analog Devices AD9554BCPZ Datasheet HTML 47Page - Analog Devices AD9554BCPZ Datasheet HTML 48Page - Analog Devices AD9554BCPZ Datasheet HTML 49Page - Analog Devices AD9554BCPZ Datasheet HTML 50Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 46 / 116 page
background image
AD9554
Data Sheet
Rev. D | Page 46 of 116
For example, Data Instruction 0x1A has a decimal value of 26;
therefore, the controller knows to transfer 27 bytes (one more
than the value of the instruction). When the controller encounters
a data instruction, it automatically reads the next two bytes because
these contain the starting address of the AD9554 register map.
The starting address is the LSB, and then the MSB. For example,
storing five bytes at Starting Address 0x00FE is entered into the
EEPROM buffer segment as 0x04, then 0xFE, and then 0x00.
Note that the internal EEPROM controller always starts at the
register map starting address and counts upward, regardless of
the mode of the main serial port.
As part of the transfer process during an EEPROM upload, the
controller calculates a CRC-32 checksum and stores it at the end of
the data transfer. As part of the transfer process during an
EEPROM download, however, the controller again calculates
the CRC-32 checksum and compares the newly calculated
checksum with the one that was stored during the upload process.
If an upload/download checksum pair does not match, the
controller sets the EEPROM fault status bit. If the upload/download
checksums match for all instructions encountered during a
download sequence, the controller sets the EEPROM complete
status bit.
Table 24. EEPROM Controller Instruction Set
Instruction
Value (Hex)
Instruction Type
Bytes
Needed
Description
0x00 to 0x7F
Data
3
A data instruction tells the controller to transfer data to or from the device settings part
of the register map. A data instruction requires two additional bytes that, together,
indicate a starting address in the register map. Encoded in the data instruction is the
number of bytes to transfer, which is one more than the instruction value.
0x80
IO_UPDATE
1
The controller issues a soft IO_UPDATE (that is analogous to the user writing
Register 0x000F = 0x01).
0x90
Calibrate all PLLs
1
The EEPROM controller initiates a calibration sequence to the SYSCLK PLL, as well as all of
the APLLs, while downloading from the EEPROM. APLL calibration does not start until
the SYSCLK PLL is stable.
0x91
Calibrate SYSCLK
1
When the controller encounters this instruction while downloading from the EEPROM, it
initiates an SYSCLK calibration sequence.
0x92
Calibrate all APLLs
1
The controller initiates an APLL calibration sequence to all four APLLs while downloading
from the EEPROM. APLL calibration is gated by the system clock being stable.
0x93/0x94/
0x95/0x96
Calibrate
APLL_0/APLL_1/
APLL_2/APLL_3
1
When the controller encounters this instruction while downloading from the EEPROM, it
initiates an APLL_0/APLL_1/APLL_2/APLL_3 calibration sequence. APLL calibration is
gated by the system clock being stable. 0x93 is for APLL_0, 0x94 is for APLL_1, and so on.
0x98
Set user free run
mode (all PLLs)
1
When the controller encounters this instruction while downloading from the EEPROM, it
forces all of the DPLLs into user free run mode. The force state is cleared automatically
when EEPROM loading is complete. However, the user free run bits in the register map
are not changed with this command and retain their programmed values.
0x99/0x9A/
0x9B/0x9C
Set DPLL_0/
DPLL_1/DPLL_2/
DPLL_3 user free
run mode
1
When the controller encounters this instruction while downloading from the EEPROM, it
forces DPLL_0/DPLL_1/DPLL_2/DPLL_3 into user free run mode. The force state is cleared
automatically when EEPROM loading is complete. However, the user free run bits in the
register map are not changed with this command, and retain their programmed values.
0xA0
Distribution sync
(all outputs)
1
When the controller encounters this instruction while downloading from the EEPROM, it
issues a sync pulse to the PLL0, PLL1, PLL2, and PLL3 channel dividers. Note that the
APLL associated with a given channel must be locked before the sync pulse reaches the
output dividers of that channel.
0xA1/0xA2/
0xA3/0xA4
Distribution sync
(PLL0/PLL1/PLL2/
PLL3 outputs)
1
When the controller encounters this instruction while downloading from the EEPROM, it
issues a sync pulse to the PLL0/PLL1/PLL2/PLL3 channel dividers. Note that, unless over-
ridden, this sync pulse is gated by the APLL lock detect signal associated with that channel.
0xB0
Clear condition
1
0xB0 is the null condition instruction.
0xB1 to 0xBF
Condition
1
0xB1 to 0xBF are condition instructions and correspond to Condition 1 through
Condition 15, respectively.
0xFE
Pause
1
When the controller encounters this instruction in the scratchpad while uploading to the
EEPROM, it resets the scratchpad address pointer and holds the EEPROM address pointer
at its last value. This allows storage of more than one instruction sequence in the
EEPROM. The controller does not copy this instruction to the EEPROM during upload.
0xFF
End of data
1
When the controller encounters this instruction in the scratchpad while uploading to the
EEPROM, it resets both the scratchpad address pointer and the EEPROM address pointer and
then enters an idle state. When the controller encounters this instruction while downloading
from the EEPROM, it resets the EEPROM address pointer and then enters an idle state.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com