FXLS8964AF datasheet(75/98 Pages) NXP

75 / 98 page

NXP Semiconductors

FXLS8964AF

3-Axis Low-g Accelerometer

FXLS8964AF

All information provided in this document is subject to legal disclaimers.

Objective data sheet

Rev. 2 — 30 October 2020

75 / 98

Table 96. SDCD_INT_SRC1 register (address 2Dh) bit description

Field

Description

OT_EA

SDCD outside-of-thresholds event active flag

0 (default): Event flag has not been asserted; the data for all enabled axes is within the window

defined by

SDCD_UTHS and SDCD_LTHS registers.

1: One or more of the enabled axes' sensor data (absolute mode) or deltas (relative mode) sits on or

outside of (for example, (data or delta) ≤

SDCD_LTHS or (data or delta) ≥ SDCD_UTHS) the upper

or lower thresholds specified in the

SDCD_UTHS and SDCD_LTHS registers. The OT_EA flag is

set whenever (X_OT_EF | Y_OT_EF | Z_OT_EF

) evaluates to true for a number of ODR periods ≥

SDCD_OT_DBCNT.

Note:

• The axes selected for participation in the over thresholds condition evaluation are enabled via the

X/Y/Z_OT_EN bits in the

SDCD_CONFIG1 register. If none of the X/Y/Z_OT_EN bits are set then

the SDCD_OT function is effectively disabled.

• When SENS_CONFIG4[WAKE_SDCD_OT] = 1, the Auto-WAKE/SLEEP timer is reset on every

ODR cycle when the OT_EA flag is asserted (set), which will prevent the device from transitioning

into SLEEP mode. This flag must be de-asserted (cleared) in order for FXLS8964AF to transition to

SLEEP mode.

X_OT_EF

X-axis data or delta-outside-of-upper-and-lower-thresholds event flag; enabled if X_OT_EN = 1

0: X-axis data or delta is <

SDCD_UTHS value and > SDCD_LTHS value.

1: X-axis data or delta is either ≥

SDCD_UTHS value or ≤ SDCD_LTHS value; the X_OT_POL flag

may be used to determine which threshold has been met or crossed.

X_OT_POL[1][2]

X-axis outside-of-thresholds polarity flag

0: X-axis data or delta was ≤ lower threshold value

1: X-axis data or delta was ≥ upper threshold value

Y_OT_EF

Y-axis data or delta-outside-of-upper-and-lower-thresholds event flag; enabled if Y_OT_EN = 1

0: Y-axis data or delta is <

SDCD_UTHS value and > SDCD_LTHS value.

1: Y-axis data or delta is either ≥

SDCD_UTHS value or ≤ SDCD_LTHS value; the Y_OT_POL flag

may be used to determine which threshold has been met or crossed.

Y_OT_POL[1][2]

Y-axis outside-of-thresholds polarity flag

0: Y-axis data or delta was equal to or below lower threshold value

1: Y-axis data or delta was equal to or above upper threshold value

Z_OT_EF[1][2]

Z-axis data or delta-outside-of-upper-and-lower-thresholds event flag; enabled if Z_OT_EN = 1

0: Z-axis data or delta is <

SDCD_UTHS value and > SDCD_LTHS value

1: Z-axis data or delta is either ≥

SDCD_UTHS value or ≤ SDCD_LTHS value; the Z_OT_POL flag

may be used to determine which threshold has been met or crossed

Z_OT_POL

Z-axis outside-of-thresholds polarity flag

0: Z-axis data or delta was equal to or below lower threshold value

1: Z-axis data or delta was equal to or above upper threshold value

[1]

This flag is only meaningful if X/Y/Z_OT_EF = 1; their individual states are latched when the X/Y/Z_OT_EF flag(s) are set, regardless of the state of

SDCD_CONFIG1[OT_ELE].

[2]

When SDCD_CONFIG1[OT_ELE] = 0, these flags are updated when X/Y/Z_OT_EF = 1 and the SDCD_OT_DBCNT value is reached.

13.31.2 SDCD_INT_SRC2 register (address 2Eh)

This register contains the SDCD within-thresholds event status flags. The WT_EA flag

may be used to signal interrupts to a host processor are mapped to one of the INT1 or

INT2 pins.

FXLS8964AF Datasheet(PDF) 75 Page - NXP Semiconductors

FXLS8964AF Datasheet(HTML) 75 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

Datasheet Download

Link URL