FXLS8964AF datasheet(76/98 Pages) NXP

76 / 98 page

NXP Semiconductors

FXLS8964AF

3-Axis Low-g Accelerometer

FXLS8964AF

All information provided in this document is subject to legal disclaimers.

Objective data sheet

Rev. 2 — 30 October 2020

76 / 98

Table 97. SDCD_INT_SRC2 register (address 2Eh) bit allocation

Bit

Name

WT_EA

—

X_WT_EF

—

Y_WT_EF

—

Z_WT_EF

—

Reset

Access

Table 98. SDCD_INT_SRC2 register (address 2Eh) bit description

Field

Description

WT_EA

SDCD within-thresholds event active flag

0 (default): Event flag has not been asserted; none of the input data (absolute mode) or deltas

(relative mode) for the enabled axes is within the window defined by the

SDCD_UTHS and SDCD_

LTHS registers.

1: All, or at least one of, (depending on the LOGIC function selected in

SDCD_

CONFIG2[WT_LOG_SEL]) the enabled axes' sensor data (absolute mode) or deltas (relative mode)

sits within both the upper and lower thresholds specified in the

SDCD_UTHS and SDCD_LTHS

registers (e.g., >

SDCD_LTHS, and < SDCD_UTHS). This flag is set whenever the condition is true

for a number of ODR cycles ≥

SDCD_WT_DBCNT.

Notes:

• The axes selected for participation in the within thresholds condition evaluation are enabled via the

X/Y/Z_WT_EN bits in the

SDCD_CONFIG1 register. The logic mode for the function is set in the

SDCD_CONFIG2 register. If none of the X/Y/Z_WT_EN bits are set then the SDCD_WT function is

effectively disabled.

• When SENS_CONFIG4[WAKE_SDCD_WT] = 1, the Auto-WAKE/SLEEP timer is reset on every

ODR cycle when the WT_EA flag is asserted (set), which will prevent the device from transitioning

into SLEEP mode. This flag must be de-asserted (cleared) in order for FXLS8964AF to transition to

SLEEP mode.

X_WT_EF

X-axis data or delta inside of upper and lower thresholds event flag; This flag is only valid if X_WT_

EN = 1:

0: X-axis data or delta is ≥

SDCD_UTHS value or ≤ SDCD_LTHS value.

1: X-axis data or delta is <

SDCD_UTHS and > SDCD_LTHS value.

Notes:

• The SDCD_CONFIG1[WT_ELE] bit determines the behavior of this bit. If WT_ELE = 1, the flag

is latched when WT_EA goes high, and will remain set until it is cleared by reading the

SDCD_

INT_SRC2 register. If the host wishes to know the state of this event flag, it must be read prior to

reading the

SDCD_INT_SRC2 register.

• If WT_ELE = 0, the X/Y/Z_WT_EF flags are updated if WT_EA = 1 and the SDCD_WT_DBCNT

value is reached. If WT_ELE = 0, the X/Y/Z_WT_EF flags are updated even if WT_EA = 0 when the

SDCD_WT_DBCNT value is set to 0.

Y_WT_EF

Y-axis data or delta inside of upper and lower thresholds event flag; This flag is only valid if Y_WT_

EN = 1:

0: Y-axis data or delta is ≥

SDCD_UTHS value or ≤ SDCD_LTHS value.

1: Y-axis data or delta is <

SDCD_UTHS and > SDCD_LTHS value.

Notes:

• The SDCD_CONFIG1[WT_ELE] bit determines the behavior of this bit. If WT_ELE = 1, the flag

is latched when WT_EA goes high, and will remain set until it is cleared by reading the

SDCD_

INT_SRC2 register. If the host wishes to know the state of this event flag, it must be read prior to

reading the

SDCD_INT_SRC2 register.

• If WT_ELE = 0, the X/Y/Z_WT_EF flags are updated if WT_EA = 1 and the SDCD_WT_DBCNT

value is reached. If WT_ELE = 0, the X/Y/Z_WT_EF flags are updated even if WT_EA = 0 when the

SDCD_WT_DBCNT value is set to 0.

FXLS8964AF Datasheet(PDF) 76 Page - NXP Semiconductors

FXLS8964AF Datasheet(HTML) 76 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

Datasheet Download

Link URL