Electronic Components Datasheet Search
  English  ▼

X  

ADS1294CZXGR Datasheet(PDF) 98 Page - Texas Instruments

Part # ADS1294CZXGR
Description  ADS129x Low-Power, 8-Channel, 24-Bit Analog Front-End for Biopotential Measurements
PDF  114 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI2 [Texas Instruments]
Direct Link  https://www.ti.com
Logo TI2 - Texas Instruments

ADS1294CZXGR Datasheet(HTML) 98 Page - Texas Instruments

Back Button ADS1294CZXGR Datasheet HTML 94Page - Texas Instruments ADS1294CZXGR Datasheet HTML 95Page - Texas Instruments ADS1294CZXGR Datasheet HTML 96Page - Texas Instruments ADS1294CZXGR Datasheet HTML 97Page - Texas Instruments ADS1294CZXGR Datasheet HTML 98Page - Texas Instruments ADS1294CZXGR Datasheet HTML 99Page - Texas Instruments ADS1294CZXGR Datasheet HTML 100Page - Texas Instruments ADS1294CZXGR Datasheet HTML 101Page - Texas Instruments ADS1294CZXGR Datasheet HTML 102Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 98 / 114 page
background image
Device
Microcontroller
Signal
Conditioning
(RC Filters
and
Amplifiers)
Supply
Generation
Connector
or Antenna
Ground Fill or
Ground Plane
Ground Fill or
Ground Plane
Interface
Transceiver
Ground Fill or
Ground Plane
Ground Fill or
Ground Plane
ADS1294, ADS1294R, ADS1296, ADS1296R, ADS1298, ADS1298R
SBAS459K – JANUARY 2010 – REVISED AUGUST 2015
www.ti.com
12 Layout
12.1 Layout Guidelines
Use a a low-impedance connection for ground, so that return currents flow undisturbed back to their respective
sources. For best performance, dedicate an entire PCB layer to a ground plane and route no other signal traces
on this layer. Keep connections to the ground plane as short and direct as possible. When using vias to connect
to the ground layer, use multiple vias in parallel to reduce impedance to ground.
A mixed signal layout sometimes incorporates separate analog and digital ground planes that are tied together at
one location; however, separating the ground planes is not necessary when analog, digital and power supply
components are properly placed. Proper placement of components partitions the analog, digital and power
supply circuitry into different PCB regions to prevent digital return currents from coupling into sensitive analog
circuitry. If ground plane separation is necessary, then make the connection at the ADC. Connecting individual
ground planes at multiple locations creates ground loops, and is not recommended. A single ground plane for
analog and digital avoids ground loops.
Bypass supply pins with a low-ESR ceramic capacitor. The placement of the bypass capacitors must be as close
as possible to the supply pins using short, direct traces. For optimum performance, the ground-side connections
of the bypass capacitors must also be low-impedance connections. The supply current flows through the bypass
capacitor pin first and then to the supply pin to make the bypassing most effective (also known as a Kelvin
connection). If multiple ADCs are on the same PCB, use wide power-supply traces or dedicated power-supply
planes to minimize the potential of crosstalk between ADCs.
If external filtering is used for the analog inputs, use C0G-type ceramic capacitors when possible. C0G
capacitors have stable properties and low-noise characteristics. Ideally, route differential signals as pairs to
minimize the loop area between the traces. Route digital circuit traces (such as clock signals) away from all
analog pins. Note the internal reference output return shares the same pin as the AVSS power supply. To
minimize coupling between the power-supply trace and reference return trace, route the two traces separately;
ideally, as a star connection at the AVSS pin.
It is essential to make short, direct interconnections on analog input lines and avoid stray wiring capacitance,
particularly between the analog input pins and AVSS. These analog input pins are high-impedance and
extremely sensitive to extraneous noise. Treat the AVSS pin as a sensitive analog signal and connect directly to
the supply ground with proper shielding. Leakage currents between the PCB traces can exceed the input bias
current of the ADS129x if shielding is not implemented. Keep digital signals as far as possible from the analog
input signals on the PCB.
It is important the SCLK input of the serial interface is free from noise and glitches. Even with relatively slow
SCLK frequencies, short digital signal rise and fall times may cause excessive ringing and noise. For best
performance, keep the digital signal traces short, using termination resistors as needed, and make sure all digital
signals are routed directly above the ground plane with minimal use of vias.
Figure 108. System Component Placement
98
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: ADS1294 ADS1294R ADS1296 ADS1296R ADS1298 ADS1298R



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com