| Electronic Components Datasheet Search |
|
SC4000 Datasheet(PDF) 17 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
SC4000 Datasheet(HTML) 17 Page - NXP Semiconductors |
|
17 / 52 page ![]() 2000 Sep 07 17 Philips Semiconductors Preliminary specification Universal Timeslot Interchange SC4000 CLKFAIL Timing and Control When an SC4000 is enabled to be clock master (C_0 = 1), the chip drives clock and frame sync signals to the SCbus and pulls the CLKFAIL line low. If the SC4000 is then disabled as clock master, the internal state machine waits for the next frame boundary and then stops driving clock and frame sync signals. Instead, it drives the CLKFAIL line high for one clock before tri-stating it (CLK- FAIL is pulled up with 4.7K on every board). An “armed” clock master (C_1 = 1) contains logic that monitors the CLKFAIL line (C_51 must be set). If CLKFAIL is sampled high for two con- secutive clock periods, then the C_0 bit is automatically set; the armed master then begins driving clock and frame sync signals and pulls CLKFAIL low. Since the internal state machine was using the clock and frame sync signals driven by the previous master, the new master takes over without any framing error. It is as if one clock period had been stretched, as shown in Figure 14. Message Channel Interface The SC4000 is designed for use with an HDLC controller to implement the mes- sage channel interface. The interface be- tween an HDLC controller and SC4000 consists of the 2.048 MHz MC_CLK (pin 11), TXD_0 (pin 9) and RXD (pin 10) lines. Data read from the SCbus MC (pin 80) line is passed straight through the SC4000 to the RXD output. Data read from TXD_0 can be passed straight through the SC4000 to the MC output, or be buffered internally through a clocked register. Buffering output data is controlled by C_12. When the Message Channel is Disabled (C_15 = 1), TXD_0 is looped back to the RXD to allow diagnostics to be run on the HDLC controller. Operation Mode and Configuration Register Setup The SC4000 can be configured to func- tion in five different modes shown in the tables below: • SCbus Clock Slave (Table 1) • SCbus Clock Master (Table 2) • SCbus Armed Clock Master (Table 3) • MVIP Clock Master (Table 4) • MVIP Clock Slave (Table 5) Table 6 shows signals that are cross referenced by SCbus and MVIP. Table 1. Configuration Register Setup for SCbus Clock Slave Operation Mode Conguration Register Bits Setup Function Description SCbus Slave C_0 = 0 SCbus clock master disabled (Default) C_1 = 0 SCbus clock master disarmed (Default) C_2 SCbus Primary or Alternate Select 0: Primary SCbus signals selected (Default) 1: Alternate SCbus signals selected C_3 = 0 Diagnostic mode disabled (Note) C_[5:4] SCbus Framing mode to select one of the following rate: 0X = 2.048 Mb/s, 256 Bits/Frame, 32 Timeslots/Frame (Default) 10 = 4.096 Mb/s, 512 Bits/Frame, 64 Timeslots/Frame 11 = 8.192 Mb/s, 1024 Bits/Frame, 128 Timeslots/Frame C_[7:6] Local bus Framing mode to select one of the following rate: 0X = 2.048 Mb/s, 256 Bits/Frame, 32 Timeslots/Frame (Default) 10 = 4.096 Mb/s, 512 Bits/Frame, 64 Timeslots/Frame 11 = 8.192 Mb/s, 1024 Bits/Frame, 128 Timeslots/Frame Note: Default of all configuration register bits except C_3 are 0 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |